Safety instructions

Safety instructions

Unipi 1.1

$/!\$

IMPORTANT: The following are important safety instructions regarding the installation, operation and maintenance of the device. Please read these instructions carefully before installation and use. Failure to follow them may result in electric shock and injury, fire, or damage to the device.

Symbols and notes

The safety signs and notices below are used across the entire online documentation.

The safety notices are classified according to the severity of the danger:

$/!\$

Danger: Imminent danger to life! Warns of situations that could result in serious injury or death if the instructions in this online manual are not followed.

$/!\$

Warning: Possible life-risking! Warns of situations that could result in serious injury or death if the instructions in this online manual are not followed.

$/!\$

Caution: If the instructions in this online manual are not followed, injury may occur.

(i)

Note: Installation recommendation or warning against possible damage to the device and connected peripherals.

The safety signs, based on EN ISO 7010, specifies safety warnings.

(i)

General warning sign

(i)

Warning sign; Electricity

(i)

Refer to instruction manual

(i)

Disconnect before carrying out maintenance or repair

General safety notice

This device is intended for use only in accordance with its specifications and applicable safety standards.
All connected external peripherals should comply with all relevant directives and standards applicable to the method of use and the country in which the device is operated.
The manufacturer is not responsible for any damage caused by improper use, incorrect installation, or modifications to the device.
Installation must be carried out by a qualified person in accordance with local electrical regulations.
The user must not disassemble or repair the device – repairs may only be performed by an authorized service center.

Compliance with directives:
This device comply with EMC, LVD, RoHS and WEEE directives applicable to European Union countries.

LVD	2014/35/EU
EMC	2014/30/EU
RoHS	2015/863/EU
WEEE	2012/19/EU

Electrical safety

Ensure that the power supply voltage matches the specified values indicated on the device label or in the manual. Using an incorrect power source may cause damage to the device and/or connected peripherals.
Do not connect the device to power if it is damaged or shows signs of malfunction.
Ensure that wires/cables are installed with proper strain relief.
Wires/cables must not be exposed to mechanical damage or environmental conditions that could degrade the cable isolation.

$/↯\$

Warning:
Take extra care when plugging in, there is a risk of electric shock! Always disconnect the device from all voltage sources (power supply, relays, etc.) before installation or maintenance.

Installation and mounting

Installation must be carried out by a qualified person in accordance with local electrical regulations.
Ensure compliance with the manual when installing the device.
Ensure that terminal blocks and electrical connections are firmly tightened and correctly wired.
Ensure separation of AC voltage cabling or high-voltage DC circuits with high-frequency switching cycles from signal wires and buses.
Keep cable lengths as short as possible. For longer cables or depending on the environment, use shielded cables.

$/!\$

Warning:
Improper handling may result in significant property damage, injury, or death. The cabinet in which the device is installed must be accessible only with a key or special tool. Only authorized personnel may have access to the device.

The device may only be installed indoors and in an environment that meets the manual (interiors with suitable temperature and humidity, cabinets protected from water ingress, etc.).

Operational safety

Use the device only for the purpose for which it was designed.
Ensure compliance with the operating parameters (manual) of the device.
Do not use the device in environments with extreme temperatures, high humidity, or chemical vapors.
Do not expose the device to direct sunlight or heat sources.
The maximum temperature of the air entering the device must not exceed the values specified in the operating parameters.
Do not overload the device beyond its rated values.
If abnormal operation occurs (e.g. overheating, burning smell, smoke), immediately disconnect the equipment from the power supply and contact service.

$/!\$

Danger:
Never use the device in areas with an explosion hazard!

Maintenance and service

$/!\$

Warning:
Before maintenance, make sure the environment and equipment are disconnected from all voltage sources.

Regularly check the condition of power cables and connectors.
Regular maintenance is recommended for the device to ensure the tightening of connector terminal screws.
When cleaning dust, use a long-bristle brush in combination with a vacuum cleaner to prevent dust from being blown around. Always keep the vacuum nozzle at a sufficient distance from the device! You may also use compressed air (with minimal humidity) to blow dust from the interior of the device, again in combination with the vacuum cleaner.
Never tamper with the internal parts of the device.
In case of malfunction, contact authorized service, do not carry out repairs yourself.

Environmental protection and disposal

Unipi devices are designed and manufactured to closely meet the requirements for environmental protection.
Do not dispose of the device in municipal waste - it contains electronic components that are recyclable.
Dispose of the device in accordance with local waste disposal regulations.
You can return the used device at designated e-waste collection points.

This device is in accordance with WEEE directive.

Waste Electrical and Electronic Equipment directive (WEEE) aims to:

Reduce the waste from Electrical and Electronic Equipment (EEE).
Introduce responsibility to EEE manufacturers for environmental impact of their products, especially at the end of the products life.
Support the separate collection, processing, reusability, usage, recycling and ecological disposal of EEE.
Prevent potential negative impacts on environment and human health from dangerous substances in EEE and to recycle and reuse its materials.

WEEE Directive Statement for the European Union:
This device cannot be disposed of as municipal waste. Different rules for handling electric waste may apply in other jurisdictions.

Table of Contents

Safety instructions

Symbols and notes

General safety notice

Electrical safety

Installation and mounting

Operational safety

Maintenance and service

Environmental protection and disposal