Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:automation:poe-splitter-hidden [2023/03/17 10:25] – [Powering Unipi units through PoE] avsetulaen:automation:poe-splitter-hidden [2023/11/27 19:23] (current) – [Connection example] avsetula
Line 2: Line 2:
 <WRAP group> <WRAP group>
 <WRAP half column 81%> <WRAP half column 81%>
-This tutorial describes the connection of Unipi controllers using 802.3at PoE+ splitter. This connection is useful especially if you need to place the PLC in locations lacking a conventional 110 / 230 V~ socket (ie. sensor stations). This tutorial will show you how to power the Unipi over Ethernet cable while retaining local network connectivity.+This tutorial describes the connection of Unipi controllers using 802.3at PoE+ splitter. The splitter must be supplemented and powered by a PoE injector or any PoE switch. This connection is useful especially if you need to place the controller in locations lacking a conventional 110 / 230 V~ socket (ie. sensor stations). This tutorial will show you how to power the Unipi over Ethernet cable while retaining local network connectivity.
 </WRAP> </WRAP>
 <WRAP half column 15%> <WRAP half column 15%>
Line 17: Line 17:
   * Cat6 network cable (RJ45)   * Cat6 network cable (RJ45)
   * conductor (Cu, 0.5mm2)   * conductor (Cu, 0.5mm2)
-  * Planet IPOE-162S PoE splitter ([[https://www.unipi.technology/ipoe-162s-splitter-p432|e-shop link]]) +  * Planet IPOE-162S PoE splitter ([[https://www.unipi.technology/ipoe-162s-splitter-p432?categoryId=15|e-shop link]]) 
-  * Planet GSD-908HP network switch +  * Planet IPOE-162 PoE injector ([[https://www.unipi.technology/ipoe-162-injector-p433?categoryId=15|e-shop link]]) 
-    * The switch used is just one of possible variants. You can use any 802.3at PoE+ standard network switch. +  * Unipi controller 
-  * Unipi PLC+
  
 ==== Connection example ==== ==== Connection example ====
-{{ :en:automation:unipi_-_switch_a_splitter.png?direct |}}+{{ :en:automation:unipi_-_injector_a_splitter.png?direct |}} 
 == Planet IPOE-162S == == Planet IPOE-162S ==
   - set the splitter for 24 V⎓ voltage using the onboard switch   - set the splitter for 24 V⎓ voltage using the onboard switch
   - connect the splitter’s V+ clamp to the PLC’s 24V clamp   - connect the splitter’s V+ clamp to the PLC’s 24V clamp
   - connect the splitter’s V- clamp to the PLC’s GND clamp   - connect the splitter’s V- clamp to the PLC’s GND clamp
-  - using the network cable, connect the splitter’s Data Out port with the PLC’s ETH port +  - using the network cable, connect the splitter’s **Data Out** port with the controller’s **ETH** port 
-  - plug an 802.3at PoE+ compatible network cable into the splitter‘s PoE In port+  - plug an 802.3at PoE+ compatible network cable into the splitter‘s **PoE In** port
  
 == Planet GSD-908HP == == Planet GSD-908HP ==
-  - use one of the switch ports to connect it with the PoE In port on the splitter via a suitable network cable +  - connect **Ethernet+DC** port to the **PoE In** port on the splitter via a suitable network cable 
-  - repeat the step for any other additional splitter +  - connect the WAN network cable into the **Ethernet** port
-  - connect the WAN network cable into the port 9 +
 ==== Technical data ==== ==== Technical data ====
-Using a single splitter to power multiple PLCs is not recommended! +Using a single splitter to power multiple controllers is not recommended! 
 \\ \\
 \\ \\
(Still can't find what you're looking for?)