Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| en:automation:poe-splitter-hidden [2023/11/27 19:19] – avsetula | en:automation:poe-splitter-hidden [2023/11/27 19:23] (current) – [Connection example] avsetula | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column 81%> | <WRAP half column 81%> | ||
| - | This tutorial describes the connection of Unipi controllers using 802.3at PoE+ splitter. The splitter must be supplemented and powered by a PoE injector or any PoE switch. This connection is useful especially if you need to place the PLC in locations lacking a conventional 110 / 230 V~ socket (ie. sensor stations). This tutorial will show you how to power the Unipi over Ethernet cable while retaining local network connectivity. | + | This tutorial describes the connection of Unipi controllers using 802.3at PoE+ splitter. The splitter must be supplemented and powered by a PoE injector or any PoE switch. This connection is useful especially if you need to place the controller |
| </ | </ | ||
| <WRAP half column 15%> | <WRAP half column 15%> | ||
| Line 19: | Line 19: | ||
| * Planet IPOE-162S PoE splitter ([[https:// | * Planet IPOE-162S PoE splitter ([[https:// | ||
| * Planet IPOE-162 PoE injector ([[https:// | * Planet IPOE-162 PoE injector ([[https:// | ||
| - | | + | * Unipi controller |
| - | * The switch used is just one of possible variants. You can use any 802.3at PoE+ standard network switch. | + | |
| - | | + | |
| ==== Connection example ==== | ==== Connection example ==== | ||
| - | {{ : | + | {{ : |
| == Planet IPOE-162S == | == Planet IPOE-162S == | ||
| - set the splitter for 24 V⎓ voltage using the onboard switch | - set the splitter for 24 V⎓ voltage using the onboard switch | ||
| - connect the splitter’s V+ clamp to the PLC’s 24V clamp | - connect the splitter’s V+ clamp to the PLC’s 24V clamp | ||
| - connect the splitter’s V- clamp to the PLC’s GND clamp | - connect the splitter’s V- clamp to the PLC’s GND clamp | ||
| - | - using the network cable, connect the splitter’s **Data Out** port with the PLC’s **ETH** port | + | - using the network cable, connect the splitter’s **Data Out** port with the controller’s **ETH** port |
| - plug an 802.3at PoE+ compatible network cable into the splitter‘s **PoE In** port | - plug an 802.3at PoE+ compatible network cable into the splitter‘s **PoE In** port | ||
| Line 35: | Line 34: | ||
| - connect **Ethernet+DC** port to the **PoE In** port on the splitter via a suitable network cable | - connect **Ethernet+DC** port to the **PoE In** port on the splitter via a suitable network cable | ||
| - connect the WAN network cable into the **Ethernet** port | - connect the WAN network cable into the **Ethernet** port | ||
| - | |||
| - | == Planet GSD-908HP == | ||
| - | - use one of the switch ports to connect it with the **PoE In** port on the splitter via a suitable network cable | ||
| - | - connect the WAN network cable into the port 9 | ||
| - | |||
| ==== Technical data ==== | ==== Technical data ==== | ||
| - | Using a single splitter to power multiple | + | Using a single splitter to power multiple |
| \\ | \\ | ||
| \\ | \\ | ||
