Differences

This shows you the differences between two versions of the page.

--- en:hw:007-patron:01-first-steps [2025/04/03 19:10] – avsetula
+++ en:hw:007-patron:01-first-steps [2026/08/03 13:13] (current) – clarification ofojt
@@ Line 1: / Line 1: @@
 ====== First steps ======
+<WRAP group>
+<WRAP half column 100%>
+#;;
+<html><style>h1 {margin-bottom: 10px !important;}</style><span class="tag-skelet inline-tag mobile-only">
+<span class="tag-patron">Patron</span>
+</span></html>
+#;;
+</WRAP>
+</WRAP>
 The Unipi Patron unit is delivered with the Linux Debian operating system, that already includes the SW platform [[en: sw: 01-mervis | Mervis]]. This article assumes Unipi Patron unit is in factory settings.
@@ Line 30: / Line 40: @@
 {{page>en:hw:007-patron:01-first-steps:regular-mode-hidden}}
+===== Connecting the power supply =====
+<WRAP group center round box 95%>
+{{ :files:img_warning-line_o.png?nolink |}}
+<WRAP half column 13%>
+{{:en:hw:02_safety-instructions_ISO-7010-W012.png?nolink |/↯\}}
+</WRAP>
+<WRAP half column 83%>
+**Warning**: \\
+Take extra care when plugging in, there is a risk of electric shock! Always ensure and check that the environment and device are disconnected from all voltage sources before starting work.
+</WRAP>
+</WRAP>
+<WRAP group center round box 95%>
+{{ :files:img_warning-line_b.png?nolink |}}
+<WRAP half column 13%>
+{{ :en:hw:01_safety-instructions_ISO-7010-W001.png?nolink |/!\}}
+</WRAP>
+<WRAP half column 83%>
+**Attention:** \\
+Make sure to connect the power supply last. Connection and disconnection of other interfaces should be done with power supply disconnected; otherwise, the device can be damaged.
+</WRAP>
+</WRAP>
+To ensure correct operation of the device, it is necessary to first connect the 24V power supply wires to the contacts as described on the device, +24V/positive contact and GND/negative contact of the detachable screw terminal block.
+Use the appropriate flathead screwdriver to install the power wires into the terminals.
+Do not exceed the maximum tightening torque specified in [[.:technical-parameters#storage_installation_and_working_conditions|technical parameters]].
+For information on recommended supply voltage tolerance and power consumption, refer to [[.:technical-parameters#storage_installation_and_working_conditions|operating conditions]] and the product label.
+;#;
+//Power supply connection//
+;#;
+{{ :en:hw:04_first-steps_power-supply.png?direct&200 |}}
+<WRAP group center round box 95%>
+{{ :files:img_warning-line_b.png?nolink |}}
+<WRAP half column 13%>
+{{ :en:hw:08_safety-instructions_pseudo-ISO-7010-info.png?nolink |(!)}}
+</WRAP>
+<WRAP half column 83%>
+**Tip:** \\
+Unipi Patron can be powered by [[https://www.unipi.technology/power-supplies-c15|24 V⎓ power supply]].
+</WRAP>
+</WRAP>
+<WRAP group center round box 95%>
+{{ :files:img_warning-line_o.png?nolink |}}
+<WRAP half column 13%>
+{{ :en:hw:02_safety-instructions_ISO-7010-W012.png?nolink |/↯\}}
+</WRAP>
+<WRAP half column 83%>
+**Warning**: \\
+The device has appliance class I. To protect against electric shock and to comply with electromagnetic compatibility (EMC), it is necessary to connect ground conductor to ground connector of the device marked on the case with symbol {{:files:earth_ground.png?nolink&16|(⏚)}}. For ground conductor connection use ring tongue and provided M4 screw with serrated lock washer.
+{{ :files:img_breakline_2.png?nolink |}}
+DIN rail on which the device is installed must be connected to the main protective earth point of the cabinet/box as well.
+</WRAP>
+</WRAP>
 {{page>en:hw:007-patron:01-first-steps:connection-to-mervishmi-hidden}}