Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:hw:007-patron:download-image:01-mervis-old-hidden [2023/05/10 12:47] avsetula |
en:hw:007-patron:download-image:01-mervis-old-hidden [2023/05/11 15:30] (current) avsetula |
||
|---|---|---|---|
| Line 22: | Line 22: | ||
| ---- | ---- | ||
| + | |||
| + | {{page>en:hw:007-patron:download-image:mervis-os-intro-old-hidden}} | ||
| {{page>en:files:software:os-images:patron-mervis-os-old-hidden}} | {{page>en:files:software:os-images:patron-mervis-os-old-hidden}} | ||
| Line 27: | Line 29: | ||
| ---- | ---- | ||
| - | <WRAP group> | + | {{page>en:hw:007-patron:download-image:mervis-os-info-hidden}} |
| - | <WRAP half column> | + | |
| - | <WRAP center round important> | + | |
| - | <wrap em>Every unit with Mervis OS 2.3.0 and newer requires a license.</wrap> | + | |
| - | + | ||
| - | {{ :files:img_breakline_gray.png?nolink |}} | + | |
| - | + | ||
| - | If the unit is not licenced, it will run in demo mode. The demo mode does not limit the functionality, but the program will run only for 20 minutes. After that time, the program will stop running and RUN LEDs will start blinking in a 2-second interval (on/off). | + | |
| - | + | ||
| - | {{ :files:img_breakline_gray.png?nolink |}} | + | |
| - | + | ||
| - | Make sure to **[[en:sw:01-mervis:updating-a-runtime-hidden|Update Runtime at first]]** and then **[[en:sw:01-mervis:use-mervis-runtime-licence-hidden| license the unit]]**. | + | |
| - | </WRAP> | + | |
| - | + | ||
| - | <WRAP center round info> | + | |
| - | Mervis OS are versioned the same way as Mervis IDE releases. Eg. Mervis OS 2.3.0.x will work with IDE 2.3.0 but might not work with IDE 2.2.0. Mervis IDE 2.3.0 requires Mervis OS 2.2.0.x at least, but also requires [[en:sw:01-mervis:updating-a-runtime-hidden|update of the Mervis RT]]. Compatibility with Mervis OS older than 2.2.0 is not guaranteed. | + | |
| - | </WRAP> | + | |
| - | </WRAP> | + | |
| - | + | ||
| - | <WRAP half column> | + | |
| - | <WRAP center round info> | + | |
| - | **SSH** is disabled on these OS images by default for security reasons. | + | |
| - | + | ||
| - | {{ :files:img_breakline_gray.png?nolink |}} | + | |
| - | + | ||
| - | If connection to the unit via SSH is required, it can be enabled either in [[en:hw:007-patron:service-mode|service mode]], or by [[en:sw:01-mervis:updating-a-runtime-configuration-hidden#unipi_specific|uploading configuration]] of Mervis RT. | + | |
| - | + | ||
| - | The default SSH credentials are: user ''unipi'' and password ''unipi.technology''. | + | |
| - | + | ||
| - | After finishing work, [[en:automation:securing-os-ssh-hidden|it is necessary to turn off or secure SSH]]. | + | |
| - | </WRAP> | + | |
| - | + | ||
| - | <WRAP center round important> | + | |
| - | After flashing the new OS always [[en:sw:01-mervis:unipi-configure-module-hidden|upload I/O boards configuration]]. After uploading the configuration, wait approximately one minute for the drive to fully boot. | + | |
| - | </WRAP> | + | |
| - | </WRAP> | + | |
| - | </WRAP> | + | |
| /* Pro funkci tlačítek posouvání menu - při malé šířce stránky */ | /* Pro funkci tlačítek posouvání menu - při malé šířce stránky */ | ||
| {{page>:av-script-horizontal-menu}} | {{page>:av-script-horizontal-menu}} | ||
