Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
en:hw:007-patron:service-mode [2021/03/11 11:31] avsetula |
en:hw:007-patron:service-mode [2021/03/16 12:16] avsetula |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| ===== Startup in a service mode ===== | ===== Startup in a service mode ===== | ||
| - | The service mode is accessed using the **SERVICE** button located above the red LED on the Unipi Gate device front plate. As the device's Ethernet ports work in bridge mode (br0 = ETH0 + ETH1) when the device is in the service mode, the ports should never be connected into the same network. The mode is physically indicated by the PWR diode continously emitting with the remaining LEDs blinking ([[en:hw:025-gate:led-indication#pwr_is_on_the_rest_is_blinking_600ms|demonstration here]] / [[en:hw:025-gate:led-indication#service_mode|startup simulator here]]). | + | The **SERVICE** button, usually located next to USB labels, is important for accessing the service mode. The mode is indicated by the slow blinking of all LEDs both in the upper and lower LED row in section 1. |
| - | {{page>en:hw:025-gate:service-web-interface-hidden}} | + | {{page>en:hw:007-patron:service-web-interface-hidden}} |
| - | As the next step for both cases, enter the device's IP address into your web browser's address bar. Upon confirmation, you will be connected to the Unipi Gate service interface. | + | As the next step for both cases, enter the device's IP address into your web browser's address bar. Upon confirmation, you will be connected to the Unipi Patron service interface. |
| ===== Description of the service web interface ===== | ===== Description of the service web interface ===== | ||
| Line 27: | Line 27: | ||
| ---- | ---- | ||
| - | <html><span class="kbBlueText">Under the ribbon are the following dialogue windows:</span></html> FIXME - | + | <html><span class="kbBlueText">Under the ribbon are the following dialogue windows:</span></html> |
| - **Settings** -> contains four buttons, all of them useable only in the regular mode:: | - **Settings** -> contains four buttons, all of them useable only in the regular mode:: | ||
| * Set 192.168.200.200 on eth0 -> sets the ethernet interface to fixed 192.168.200.200 IP address | * Set 192.168.200.200 on eth0 -> sets the ethernet interface to fixed 192.168.200.200 IP address | ||
| Line 38: | Line 38: | ||
| - **Messages** -> displays a list of performed operations | - **Messages** -> displays a list of performed operations | ||
| \\ | \\ | ||
| - | <WRAP center round info 80%> FIXME | + | <WRAP center round info 80%> |
| - | Dialogové okno **Settings** může obsahovat ještě 3 další tlačítka, pokud je na jednotce SW Mervis. | + | If Mervis is used, the **Settings** dialogue window can contain 3 additional buttons. |
| - | * Clear Mervis -> odstraní nahraný projekt, konfiguraci i webový obsah | + | * Enable Mervis -> launches Mervis RT on the device |
| - | * Enable Mervis -> spustí Mervis RT na zařízení | + | * Disable Mervis -> stops Mervis RT on the device |
| - | * Disable Mervis -> zastaví Mervis RT na zařízení | + | |
| </WRAP> | </WRAP> | ||
| + | \\ | ||
| {{ :en:hw:patron_service_mode.png?direct |}} | {{ :en:hw:patron_service_mode.png?direct |}} | ||
