Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:hw:007-patron:service-mode [2021/03/11 11:27]
avsetula
en:hw:007-patron:service-mode [2021/08/06 14:00] (current)
avsetula
Line 2: Line 2:
 <WRAP group 100%> <WRAP group 100%>
 <WRAP half column 81%> <WRAP half column 81%>
-This mode serves for uploading or backing up the operating system, or for restoring access to the PLC (restoring the default password via OS reflash, changing the network configuration or enabling/​disablíng the SSH access). Only the service web interface is available in this mode, all remaining ​PLC functions are disabled. This mode does not publish [[en:​hw:​025-gate:​01-first-steps#​mdns_record|mDNS record]]. ​+This mode serves for uploading or backing up the operating system, or for restoring access to the unit (restoring the default password via OS reflash, changing the network configuration or enabling/​disablíng the SSH access). Only the service web interface is available in this mode, all remaining ​unit functions are disabled. This mode does not publish [[en:​hw:​025-gate:​01-first-steps#​mdns_record|mDNS record]]. ​
 </​WRAP>​ </​WRAP>​
 <WRAP half column 15%> <WRAP half column 15%>
Line 12: Line 12:
  
 ===== Startup in a service mode ===== ===== Startup in a service mode =====
-The service mode is accessed using the **SERVICE** button located ​above the red LED on the Unipi Gate device front plate. As the device'​s Ethernet ports work in bridge mode (br0 = ETH0 + ETH1) when the device ​is in the service mode, the ports should never be connected into the same network. The mode is physically ​indicated by the PWR diode continously emitting with the remaining LEDs blinking ([[en:​hw:​025-gate:​led-indication#​pwr_is_on_the_rest_is_blinking_600ms|demonstration here]] / [[en:​hw:​025-gate:​led-indication#​service_mode|startup simulator here]])+The **SERVICE** button, usually ​located ​next to USB labels, ​is important for accessing ​the service mode. The mode is indicated by the slow blinking of all LEDs both in the upper and lower LED row in section 1
    
-{{page>​en:​hw:​025-gate:​service-web-interface-hidden}}+{{page>​en:​hw:​007-patron:​service-web-interface-hidden}}
  
-As the next step for both cases, enter the device'​s IP address into your web browser'​s address bar. Upon confirmation,​ you will be connected to the Unipi Gate service interface.+As the next step for both cases, enter the device'​s IP address into your web browser'​s address bar. Upon confirmation,​ you will be connected to the Unipi Patron ​service interface.
  
 ===== Description of the service web interface ===== ===== Description of the service web interface =====
Line 23: Line 23:
 <​html><​span class="​kbBlueText">​On the right side of the ribbon, there are two buttons:</​span></​html>​ <​html><​span class="​kbBlueText">​On the right side of the ribbon, there are two buttons:</​span></​html>​
   - **Run shell** -> serves for access to a console with limited options (BusyBox)   - **Run shell** -> serves for access to a console with limited options (BusyBox)
-  - **Restart system** -> reboots the controller+  - **Restart system** -> reboots the unit
  
 ---- ----
Line 29: Line 29:
 <​html><​span class="​kbBlueText">​Under the ribbon are the following dialogue windows:</​span></​html>​ <​html><​span class="​kbBlueText">​Under the ribbon are the following dialogue windows:</​span></​html>​
   - **Settings** -> contains four buttons, all of them useable only in the regular mode::   - **Settings** -> contains four buttons, all of them useable only in the regular mode::
-    ​* Set DHCP on br0 interface -> sets the bridge interface to obtain the address from DHCP +    * Set 192.168.200.200 on eth0 -> sets the ethernet ​interface to fixed 192.168.200.200 IP address 
-    ​* Set 192.168.200.200 on br0 interface ​-> sets the bridge ​interface to fixed 192.168.200.200 IP address00+    * Set DHCP on eth0 -> sets the ethernet interface to obtain the address from DHCP
     * Enable ssh -> enables SSH access on port 22 (SSH is enabled by default)     * Enable ssh -> enables SSH access on port 22 (SSH is enabled by default)
     * Disable ssh -> disables SSH access     * Disable ssh -> disables SSH access
Line 38: Line 38:
   - **Messages** -> displays a list of performed operations   - **Messages** -> displays a list of performed operations
 \\ \\
-<WRAP center round info 80%> ​FIXME +<WRAP center round info 80%> 
-Dialogové okno **Settings** ​může obsahovat ještě ​další tlačítka, pokud je na jednotce SW Mervis. +If Mervis is used, the **Settings** ​dialogue window can contain ​additional buttons
-  * Clear Mervis -> odstraní nahraný projekt, konfiguraci i webový obsah +  * Enable Mervis -> launches ​Mervis RT on the device 
-  * Enable Mervis -> spustí ​Mervis RT na zařízení +  * Disable Mervis -> stops Mervis RT on the device
-  * Disable Mervis -> zastaví ​Mervis RT na zařízení ​+
 </​WRAP>​ </​WRAP>​
 +\\
  
 {{ :​en:​hw:​patron_service_mode.png?​direct |}} {{ :​en:​hw:​patron_service_mode.png?​direct |}}