Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:hw:01-axon:iqrf [2019/09/18 14:22]
tomhora
en:hw:01-axon:iqrf [2020/11/10 16:17] (current)
avsetula
Line 1: Line 1:
 +{{page>​en:​hw:​01-axon:​replacement-of-axon-hidden}}
 ====== Axon IQRF ====== ====== Axon IQRF ======
 ===== Quick-start guide ===== ===== Quick-start guide =====
 === Module information === === Module information ===
-Type: DC)TR-76Dx +  * Type: (DC)TR-76Dx 
-OS: 4.03D +  ​* ​OS: 4.03D 
-DPA: 0403 +  ​* ​DPA: 0403 
-Network type: STD+LP +  ​* ​Network type: STD+LP 
-Firmware: Coordinator with UART communication+  ​* ​Firmware: Coordinator with UART communication
  
-=== IQRF Daemon Installation === +==== IQRF Daemon Installation ​==== 
-Axons are shipped with the latest version of Axon Mervis OS but this tutorial expects the latest version of **Axon Open-Source image** ​[[files:​software:​os-images:​00-start#​axon_generation_os|]].+Axons are shipped with the latest version of Axon Mervis OS but this tutorial ​**expects the latest version of  [[files:​software:​os-images:​00-start#​axon_opensource_os ​Axon Open-Source image]]**. Make sure to perform apt-update before proceeding to get the latest packages.
  
-To install the iqrf-gateway-daemon,​ follow the steps according to the official documentation for Debian Buster [[https://​docs.iqrf.org/​iqrf-gateway/​daemon-install.html#​buster-10]]. Make sure to install **version ​=>2.2.0** ​(currently in beta repository) ​since previous version ​do not support ​UniPi specific requirements.+To install the iqrf-gateway-daemon,​ follow the steps according to the official documentation for Debian Buster [[https://​docs.iqrf.org/​iqrf-gateway/​daemon-install.html#​buster-10]]. Make sure to install **version ​newer than 2.2.0** since the previous version ​does not support ​Unipi specific requirements.
  
-To install the iqrf-gateway-webapp simply follow the official guide. It is not needed to add the repository for the PHP7.3 since it is already included in the official Debian repository. [[ https://​docs.iqrf.org/​iqrf-gateway/​webapp-install.html#​install-iqrf-gateway-webapp ]]+To install the iqrf-gateway-webapp simply follow the official guide. It is not needed to add the repository for the PHP7.3 since it is already included in the official Debian ​Buster ​repository. [[ https://​docs.iqrf.org/​iqrf-gateway/​webapp-install.html#​install-iqrf-gateway-webapp ]]
  
-=== IQRF Daemon Configuration === +If you want to use the **iqrf-gateway-webapp**, also make sure that no other website ​is enabled on the TCP port 80 within ​the Nginx webserverE.g. delete files other than **iqrf-gateway-webapp.localhost** from the ''/​etc/​nginx/​site-enabled''​ directory.
-It's recommended ​to use the **UART** communication with the coordinator (this is the Factory FW configuration) for normal communicationSPI should be used only for re-programming of the IQRF module, because the SPI line is shared with the UniPi HW.+
  
-== UART configuration ==+==== IQRF Daemon Configuration ==== 
 +It's recommended to use the **UART** communication with the coordinator (this is the Factory FW configuration) for normal communication. SPI should be used only for re-programming of the IQRF module because the SPI line is shared with the Unipi HW.  
 + 
 +//Please note that the SPI is set as default interface in IQRF Daemon after installation. To change to the **UART**, enable IqrfUart and disable both IqrfCdc and IqrfSpi components (section Configuration->​Components in the webapp GUI).// 
 + 
 +=== UART configuration ===
 Make sure to use the following parameters: Make sure to use the following parameters:
   * IQRF UART interface: /dev/ttyS0   * IQRF UART interface: /dev/ttyS0
Line 25: Line 30:
   * UART bus enable GPIO pin: 18   * UART bus enable GPIO pin: 18
  
-== SPI configuration ==+=== SPI configuration ​===
 Make sure to use the following parameters: Make sure to use the following parameters:
   * IQRF SPI interface: /spidev0.3   * IQRF SPI interface: /spidev0.3
Line 32: Line 37:
   * Programming mode switch GPIO pin: 2   * Programming mode switch GPIO pin: 2
   * Enable SPI reset (checked)   * Enable SPI reset (checked)
-