Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
en:hw:025-gate:led-indication [2021/02/09 08:45] avsetula [Device startup modes] |
en:hw:025-gate:led-indication [2021/06/09 07:56] avsetula |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | {{page>en:hw:led-indication-css-hidden}} | ||
| + | |||
| ====== LED indication ====== | ====== LED indication ====== | ||
| <WRAP group 100%> | <WRAP group 100%> | ||
| Line 14: | Line 16: | ||
| |< 100% 25% 16% 46% 13%>| | |< 100% 25% 16% 46% 13%>| | ||
| - | ^Label ^Function ^Meaning ^Colour ^ | + | ^Label ^Function ^Meaning ^Colour ^ |
| ||||| | ||||| | ||
| - | |PWR |On/Off |The controller is on/off |Red | | + | |PWR |On/Off |The controller is on/off |Red | |
| - | |ACT |Blinking |Indication of the controller's state |Green | | + | |ACT |Blinking |Indication of the controller's state |Green | |
| - | |ACT - customized |Selectable |Based on the settings (see the note below) |Green | | + | |ACT - customized |Selectable |Based on the settings (see the note below) |Green | |
| - | |TX (RS485) |On |Indication of serial line broadcast indication |Green | | + | |TX (RS485) |On |Indication of serial line broadcasting |Green | |
| - | |RX (RS485) |On |Indication of serial line receiving |Green | | + | |RX (RS485) |On |Indication of serial line receiving |Green | |
| |ETH port |On \\ Off \\ Blinking \\ Off |Connection established \\ Connection not established \\ Communication in progress \\ Connection not established |Green \\ \\ Yellow | | |ETH port |On \\ Off \\ Blinking \\ Off |Connection established \\ Connection not established \\ Communication in progress \\ Connection not established |Green \\ \\ Yellow | | ||
| Line 104: | Line 106: | ||
| - | ==== PWR is on, the rest is blinking (600ms) ==== | + | ==== PWR is on, the rest is blinking (600 ms) ==== |
| <WRAP group> | <WRAP group> | ||
| <WRAP half column 70%> | <WRAP half column 70%> | ||
| Line 136: | Line 138: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column 70%> | <WRAP half column 70%> | ||
| - | /* | ||
| - | Při běžném spuštění sledujte diodu **ACT**. Po připojení napájení v zařízení nejprve startuje zavaděč OS "**uboot**", tento stav je signalizován prvním delším rozsvícením diody. Dokončení zavádění OS je signalizováno pohasnutím diody a velmi krátkým bliknutím. Po chvíli začne startovat OS, což je signalizováno dvojtým krátkým bliknutím diody. | ||
| - | */ | ||
| \\ Watch the **ACT** diode during a regular startup. The "**uboot**" OS bootloader will start first, indicated by the diode turning on. The finish of the bootloader start is indicated by the diode turning off with a short blink. After few moments the OS boot will start, indicated by two short blinks of the diode. \\ | \\ Watch the **ACT** diode during a regular startup. The "**uboot**" OS bootloader will start first, indicated by the diode turning on. The finish of the bootloader start is indicated by the diode turning off with a short blink. After few moments the OS boot will start, indicated by two short blinks of the diode. \\ | ||
| Line 146: | Line 145: | ||
| |< 100% 30% 28% 14% 14% 14%>| | |< 100% 30% 28% 14% 14% 14%>| | ||
| ^Behaviour description ^Meaning ^ Off ^ On ^ Off ^ | ^Behaviour description ^Meaning ^ Off ^ On ^ Off ^ | ||
| - | |ACT is on |OS bootloader (uboot) | 3000ms | 1750ms | | | + | |||||| |
| - | |ACT blinks once |Bootloader start complete | 250ms | 75ms | 1000ms | | + | |ACT is on |Bootloader start (uboot) | 3000ms | 1750ms | | |
| - | |ACT blinks twice |Booting the OS | 250ms | 75ms | | | + | |ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | |
| + | |ACT blinks twice |The controller's OS is booting | 250ms | 75ms | | | ||
| |ACT is continuously on and repeatedly turns off for a short time |The OS is running, the device is ready for use | 50ms | 2000ms | | | |ACT is continuously on and repeatedly turns off for a short time |The OS is running, the device is ready for use | 50ms | 2000ms | | | ||
| </WRAP> | </WRAP> | ||
| Line 165: | Line 165: | ||
| If you are looking up for a guide on how to enter and use the service mode, please visit the [[en:hw:025-gate:service-mode|this article]]. | If you are looking up for a guide on how to enter and use the service mode, please visit the [[en:hw:025-gate:service-mode|this article]]. | ||
| </WRAP> | </WRAP> | ||
| - | /* | ||
| - | Tlačítko **SERVICE** je sepnuto a drženo před připojením napájení, poté sledujte diodu **ACT**. Po připojení napájení v zařízení nejprve startuje zavaděč OS "**uboot**", tento stav je signalizován prvním delším rozsvícením diody. Přibližně 4 vteřiny po rozsvícení je možné tlačítko pustit, dioda stále svítí. Dokončení zavádění OS je signalizováno pohasnutím diody a velmi krátkým bliknutím. Následně začne startovat OS, což je signalizováno dvojtým krátkým bliknutím diody. | ||
| - | */ | ||
| The **SERVICE** button is pressed and held before plugging in the power supply. Then watch the ACT diode. After plugging the power supply in, the "**uboot**" bootloader will start first, indicated by the diode switching on. Roughly 4 seconds later, you can release the button - the diode will stay on. The finish of the bootloader start is indicated by the ACT diode turning off with a very short blink. After few moments the OS boot will start, indicated by two short blinks of the diode. | The **SERVICE** button is pressed and held before plugging in the power supply. Then watch the ACT diode. After plugging the power supply in, the "**uboot**" bootloader will start first, indicated by the diode switching on. Roughly 4 seconds later, you can release the button - the diode will stay on. The finish of the bootloader start is indicated by the ACT diode turning off with a very short blink. After few moments the OS boot will start, indicated by two short blinks of the diode. | ||
| Line 173: | Line 170: | ||
| |< 100% 30% 28% 14% 14% 14%>| | |< 100% 30% 28% 14% 14% 14%>| | ||
| ^Behaviour description ^Meaning ^ Off ^ On ^ Off ^ | ^Behaviour description ^Meaning ^ Off ^ On ^ Off ^ | ||
| - | |ACT is on |OS bootloader start | 3000ms | >5000ms | | | + | |ACT is on |Bootloader start (uboot) | 3000ms | >5000ms | | |
| - | |ACT blinks once |Bootloader start complete | 250ms | 75ms | 1000ms | | + | |ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | |
| - | |ACT blinks twice |The OS is booting | 250ms | 75ms | | | + | |ACT blinks twice |The controller's OS is booting | 250ms | 75ms | | |
| - | |ACT and all TX and RX diodes blink slowly |The device is in the service mode | 600ms | 600ms | | | + | |ACT and all TX and RX diodes blink slowly |The device is in service mode | 600ms | 600ms | | |
| </WRAP> | </WRAP> | ||
| Line 186: | Line 183: | ||
| - | ==== The mode for flashing the OS from a USB drive ==== | + | === Special functions of the service mode - flashing the OS from a USB drive === |
| <WRAP group> | <WRAP group> | ||
| <WRAP half column 70%> | <WRAP half column 70%> | ||
| Line 192: | Line 189: | ||
| If you are looking for a guide how to flash the OS, please visit [[en:hw:025-gate:image|this article]]. | If you are looking for a guide how to flash the OS, please visit [[en:hw:025-gate:image|this article]]. | ||
| </WRAP> | </WRAP> | ||
| - | /* | ||
| - | USB disk je připojen k zařízení a tlačítko **SERVICE** je sepnuto a drženo před připojením napájení, poté sledujte diodu **ACT**. Po připojení napájení v zařízení nejprve startuje zavaděč OS "**uboot**", tento stav je signalizován prvním delším rozsvícením diody. Přibližně 4 vteřiny po rozsvícení je možné tlačítko pustit, dioda stále svítí. Dokončení zavádění OS je signalizováno pohasnutím diody a velmi krátkým bliknutím. Následně začne startovat OS, což je signalizováno dvojtým krátkým bliknutím diody. | ||
| - | */ | ||
| - | The USB drive is inserted into the device and the **SERVICE** button is pressed and held before plugging in the power supply. Then watch the **ACT** diode. After plugging in the power supply, the "**uboot**" OS bootloader will start, indicated by the diode turning on. Roughly 4 seconds later, you can release the button - the diode will stay turned on. The finish of the bootloader start is indicated by the ACT diode turning off with a very short blink. After few moments the OS boot will start, indicated by two short blinks of the diode. | + | The USB drive is inserted into the device and the **SERVICE** button is pressed and held before plugging in the power supply. Next states of LEDs and the button are identical to the service mode until the OS is started. |
| After a while the OS boot will start, indicated by very short blinks of the **ACT** diode and all **TX**, **RX** diodes. The controller will reboot after finishing the process. | After a while the OS boot will start, indicated by very short blinks of the **ACT** diode and all **TX**, **RX** diodes. The controller will reboot after finishing the process. | ||
| - | |< 100% 30% 28% 14% 14% 14%>| | + | |< 100% 30% 28% 14% 28%>| |
| - | ^Behaviour description ^Meaning ^ Off ^ On ^ Off ^ | + | ^Behaviour description ^Meaning ^ Off ^ On ^ |
| - | |ACT is on |OS bootloader start | 3000ms | >5000ms | | | + | ||||| |
| - | |ACT blinks once |OS bootloader start complete | 250ms | 75ms | 1000ms | | + | |ACT and TX, RX diodes blink quickly |Flashing the OS | 80ms | 80ms | |
| - | |ACT blinks twice |OS boot has started | 250ms | 75ms | | | + | |
| - | |ACT and TX, RX diodes blink slowly |The device is in service mode | 80ms | 80ms | | | + | |
| </WRAP> | </WRAP> | ||
