Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:hw:025-gate:led-indication [2021/05/14 11:19] avsetula [Service mode] |
en:hw:025-gate:led-indication [2021/08/09 13:19] (current) avsetula |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | {{page>en:hw:led-indication-css-hidden}} | ||
+ | |||
====== LED indication ====== | ====== LED indication ====== | ||
<WRAP group 100%> | <WRAP group 100%> | ||
Line 14: | Line 16: | ||
|< 100% 25% 16% 46% 13%>| | |< 100% 25% 16% 46% 13%>| | ||
- | ^Label ^Function ^Meaning ^Colour ^ | + | ^Label ^Function ^Meaning ^Colour ^ |
||||| | ||||| | ||
- | |PWR |On/Off |The controller is on/off |Red | | + | |PWR |On/Off |The device is on/off |Red | |
- | |ACT |Blinking |Indication of the controller's state |Green | | + | |ACT |Blinking |Indication of the device's state |Green | |
- | |ACT - customized |Selectable |Based on the settings (see the note below) |Green | | + | |ACT - customized |Selectable |Based on the settings (see the note below) |Green | |
- | |TX (RS485) |On |Indication of serial line broadcast indication |Green | | + | |TX (RS485) |On |Indication of serial line broadcasting |Green | |
- | |RX (RS485) |On |Indication of serial line receiving |Green | | + | |RX (RS485) |On |Indication of serial line receiving |Green | |
|ETH port |On \\ Off \\ Blinking \\ Off |Connection established \\ Connection not established \\ Communication in progress \\ Connection not established |Green \\ \\ Yellow | | |ETH port |On \\ Off \\ Blinking \\ Off |Connection established \\ Connection not established \\ Communication in progress \\ Connection not established |Green \\ \\ Yellow | | ||
Line 146: | Line 148: | ||
|ACT is on |Bootloader start (uboot) | 3000ms | 1750ms | | | |ACT is on |Bootloader start (uboot) | 3000ms | 1750ms | | | ||
|ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | | |ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | | ||
- | |ACT blinks twice |The controller's OS is booting | 250ms | 75ms | | | + | |ACT blinks twice |The device's OS is booting | 250ms | 75ms | | |
|ACT is continuously on and repeatedly turns off for a short time |The OS is running, the device is ready for use | 50ms | 2000ms | | | |ACT is continuously on and repeatedly turns off for a short time |The OS is running, the device is ready for use | 50ms | 2000ms | | | ||
</WRAP> | </WRAP> | ||
Line 170: | Line 172: | ||
|ACT is on |Bootloader start (uboot) | 3000ms | >5000ms | | | |ACT is on |Bootloader start (uboot) | 3000ms | >5000ms | | | ||
|ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | | |ACT blinks once |The bootloader is running | 250ms | 75ms | 1000ms | | ||
- | |ACT blinks twice |The controller's OS is booting | 250ms | 75ms | | | + | |ACT blinks twice |The device's OS is booting | 250ms | 75ms | | |
|ACT and all TX and RX diodes blink slowly |The device is in service mode | 600ms | 600ms | | | |ACT and all TX and RX diodes blink slowly |The device is in service mode | 600ms | 600ms | | | ||
</WRAP> | </WRAP> | ||
Line 190: | Line 192: | ||
The USB drive is inserted into the device and the **SERVICE** button is pressed and held before plugging in the power supply. Next states of LEDs and the button are identical to the service mode until the OS is started. | The USB drive is inserted into the device and the **SERVICE** button is pressed and held before plugging in the power supply. Next states of LEDs and the button are identical to the service mode until the OS is started. | ||
- | After a while the OS boot will start, indicated by very short blinks of the **ACT** diode and all **TX**, **RX** diodes. The controller will reboot after finishing the process. | + | After a while the OS boot will start, indicated by very short blinks of the **ACT** diode and all **TX**, **RX** diodes. The device will reboot after finishing the process. |
|< 100% 30% 28% 14% 28%>| | |< 100% 30% 28% 14% 28%>| |