Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| en:hw:03-unipi11:extension [2021/09/10 08:08] – lpolcerova | en:hw:03-unipi11:extension [2025/04/09 15:54] (current) – avsetula | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Extension module EMO-R8 ====== | ====== Extension module EMO-R8 ====== | ||
| + | |||
| + | <WRAP group> | ||
| + | <WRAP half column 100%> | ||
| + | #;; | ||
| + | < | ||
| + | <span class=" | ||
| + | </ | ||
| + | #;; | ||
| + | </ | ||
| + | </ | ||
| + | |||
| Unipi 1.1 can be expanded by up to 56 relays. For this purpose is used the I²C expansion module EMO-R8, which can be purchased [[https:// | Unipi 1.1 can be expanded by up to 56 relays. For this purpose is used the I²C expansion module EMO-R8, which can be purchased [[https:// | ||
| - | Instructions for use with SW Mervis can be found here on this link. | + | Instructions for use with SW Mervis can be found [[en: |
| The module can be connected using the RJ11 connection cable included in the package. | The module can be connected using the RJ11 connection cable included in the package. | ||
| Line 9: | Line 20: | ||
| ===== Connectivity ===== | ===== Connectivity ===== | ||
| - | * 8× Finder 36.11.9.005.4011 switching relay (250 V~ / 10 A or 30 V⎓ / 10 A) /*FIXME - v CZ verzi chybí mezera před A, resp. 10 A */ | + | * 8× Finder 36.11.9.005.4011 switching relay (250 V~ / 10 A or 30 V⎓ / 10 A) |
| * 2× I²C port - one serves as an input (from Unipi 1.1) and the other for connecting another EMO-R8 board or another I²C extension | * 2× I²C port - one serves as an input (from Unipi 1.1) and the other for connecting another EMO-R8 board or another I²C extension | ||
| * 2.1 mm power jack (DC jack) - requires power supply of 5 V⎓ / 0,6 A | * 2.1 mm power jack (DC jack) - requires power supply of 5 V⎓ / 0,6 A | ||
| Line 15: | Line 26: | ||
| ===== Addressing ===== | ===== Addressing ===== | ||
| - | Up to 7 different addresses can be set for this expansion module, so up to 7 of these modules can be connected to Unipi 1.1. The following table describes the position of the jumpers for setting the I²C address. | + | Up to 7 different addresses can be set for this expansion module, so up to 7 of these modules can be connected to Unipi 1.1. The following table describes the position of the jumpers for setting the I²C address. |
| - | /* FIXME - v CZ tabulka Adesa místo Adresa */ | + | |
| - | |< 100% 1% 5% 5% 5% 5% 10% 10% 7% 57% >| | + | |< 100% 1% 5% 5% 5% 3% 8% 8% 9% 4% 57% >| |
| - | ^ ^ A2 ^ A1 ^ A0 ^ ^ HEX ^ DEC ^ ^ Popis ^ | + | ^ ^ A2 ^ A1 ^ A0 ^ ^ HEX ^ DEC |
| |||||||||| | |||||||||| | ||
| - | | | 0 | 0 | 0 | | 20 | 32 | | Address reserved for relay on Unipi 1.1 | | + | | | 0 | 0 | 0 | | 20 | 32 |
| - | | | 0 | 0 | 1 | | 21 | 33 | | Open address | + | | | 0 | 0 | 1 | | 21 | 33 |
| - | | | 0 | 1 | 0 | | 22 | 34 | | Open address | + | | | 0 | 1 | 0 | | 22 | 34 |
| - | | | 0 | 1 | 1 | | 23 | 35 | | Open address | + | | | 0 | 1 | 1 | | 23 | 35 |
| - | | | 1 | 0 | 0 | | 24 | 36 | | Open address | + | | | 1 | 0 | 0 | | 24 | 36 |
| - | | | 1 | 0 | 1 | | 25 | 37 | | Open address | + | | | 1 | 0 | 1 | | 25 | 37 |
| - | | | 1 | 1 | 0 | | 26 | 38 | | Open address | + | | | 1 | 1 | 0 | | 26 | 38 |
| - | | | 1 | 1 | 1 | | 27 | 39 | | Open address | + | | | 1 | 1 | 1 | | 27 | 39 | |
| + | |||
| + | ==== Modbus accessing on GNU/Linux systems ==== | ||
| + | Does not apply for Mervis OS. To use the extension board on Modbus, you have to allow it first. Follow steps in file viewed by command **cat / | ||
