Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
en:hw:03-unipi11:extension [2021/09/10 06:42] avsetula created |
en:hw:03-unipi11:extension [2021/09/10 14:31] (current) avsetula [Extension module EMO-R8] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Rozšiřující modul EMO-R8 ====== | + | ====== Extension module EMO-R8 ====== |
| - | Unipi 1.1 lze rozšířit až o 56 relé. K tomu slouží I2C rozšiřující modul EMO-R8, který lze zakoupit v [[https://www.unipi.technology/cs/8-relay-addon-emo-r8-p34|našem e-shopu]]. | + | Unipi 1.1 can be expanded by up to 56 relays. For this purpose is used the I²C expansion module EMO-R8, which can be purchased [[https://www.unipi.technology/cs/8-relay-addon-emo-r8-p34|in our e-shop]]. |
| - | Návod pro použití se SW Mervis naleznete zde v odkazu. | + | Instructions for use with SW Mervis can be found [[en:sw:01-mervis:unipi11-with-emo-r8-hidden|here on this link]]. |
| - | Modul lze připojit pomocí RJ11 propojovacího kabelu, který je součástí balení. | + | The module can be connected using the RJ11 connection cable included in the package. |
| + | {{ :en:hw:emo-r8.jpg?nolink |}} | ||
| + | ===== Connectivity ===== | ||
| + | * 8× Finder 36.11.9.005.4011 switching relay (250 V~ / 10 A or 30 V⎓ / 10 A) | ||
| + | * 2× I²C port - one serves as an input (from Unipi 1.1) and the other for connecting another EMO-R8 board or another I²C extension | ||
| + | * 2.1 mm power jack (DC jack) - requires power supply of 5 V⎓ / 0,6 A | ||
| + | * 3× jumper for setting the address according to the table | ||
| - | + | ===== Addressing ===== | |
| - | ===== Konektivita ===== | + | Up to 7 different addresses can be set for this expansion module, so up to 7 of these modules can be connected to Unipi 1.1. The following table describes the position of the jumpers for setting the I²C address. |
| - | * 8× Finder 36.11.9.005.4011 přepínací relé (250 V~ / 10 A nebo 30 V⎓ / 10A) | + | |
| - | * 2× I2C port - jeden slouží jako vstup (z Unipi 1.1) a druhý pro připojení další desky EMO-R8 | + | |
| - | * Zdířka 2,1 mm pro napájení (DC jack) - vyžaduje napájení 5 V⎓ / 0,6 A | + | |
| - | * 3× jumper pro nastavení adresy dle tabulky | + | |
| - | + | ||
| - | ===== Adresace ===== | + | |
| - | Pro tento rozšiřující modul je možné nastavit až 7 různých adres, lze tedy k Unipi 1.1 připojit až 7 těchto modulů. Následující tabulka popisuje polohu jumperů pro nastavení I2C adresy. | + | |
| |< 100% 1% 5% 5% 5% 5% 10% 10% 7% 57% >| | |< 100% 1% 5% 5% 5% 5% 10% 10% 7% 57% >| | ||
| ^ ^ A2 ^ A1 ^ A0 ^ ^ HEX ^ DEC ^ ^ Popis ^ | ^ ^ A2 ^ A1 ^ A0 ^ ^ HEX ^ DEC ^ ^ Popis ^ | ||
| |||||||||| | |||||||||| | ||
| - | | | 0 | 0 | 0 | | 20 | 32 | | Adesa rezervována pro relé na Unipi 1.1 | | + | | | 0 | 0 | 0 | | 20 | 32 | | Address reserved for relay on Unipi 1.1 | |
| - | | | 0 | 0 | 1 | | 21 | 33 | | Adesa volná | | + | | | 0 | 0 | 1 | | 21 | 33 | | Free address | |
| - | | | 0 | 1 | 0 | | 22 | 34 | | Adesa volná | | + | | | 0 | 1 | 0 | | 22 | 34 | | Free address | |
| - | | | 0 | 1 | 1 | | 23 | 35 | | Adesa volná | | + | | | 0 | 1 | 1 | | 23 | 35 | | Free address | |
| - | | | 1 | 0 | 0 | | 24 | 36 | | Adesa volná | | + | | | 1 | 0 | 0 | | 24 | 36 | | Free address | |
| - | | | 1 | 0 | 1 | | 25 | 37 | | Adesa volná | | + | | | 1 | 0 | 1 | | 25 | 37 | | Free address | |
| - | | | 1 | 1 | 0 | | 26 | 38 | | Adesa volná | | + | | | 1 | 1 | 0 | | 26 | 38 | | Free address | |
| - | | | 1 | 1 | 1 | | 27 | 39 | | Adesa volná | | + | | | 1 | 1 | 1 | | 27 | 39 | | Free address | |
