Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:hw:05-1-wire [2020/03/05 09:05] jan_kozak |
en:hw:05-1-wire [2020/06/25 12:25] avsetula removed |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======%hide 1-Wire bus ====== | + | ====== 1-Wire bus ====== |
| 1-Wire is a communication bus system designed for low-speed data transmission, signalling and power through a single wire. | 1-Wire is a communication bus system designed for low-speed data transmission, signalling and power through a single wire. | ||
| Unipi 1-Wire products are designed for reliability and serialization. For this purpose, Unipi 1-Wire sensors and hubs use a four-wire setup (GND, VCC, DATA-IN, DATA-OUT) | Unipi 1-Wire products are designed for reliability and serialization. For this purpose, Unipi 1-Wire sensors and hubs use a four-wire setup (GND, VCC, DATA-IN, DATA-OUT) | ||
| + | ===== 1-Wire temperature sensors ===== | ||
| {{ :en:hw:03-1wire:xds18b20.jpg?direct&100|}} | {{ :en:hw:03-1wire:xds18b20.jpg?direct&100|}} | ||
| - | Unipi 1-Wire temperature sensors are based on a widely used DS18B20 [[en:automation:02-glossary:1wire-hidden|1-Wire]] sensor encased in a TO-92 metal probe. The sensor converts 12-bit temperature values to a digital signal (750 ms max. delay) | + | Unipi 1-Wire temperature sensors are based on a widely used DS18B20 [[en:automation:02-glossary:1wire-hidden|1-Wire]] sensor encased in a TO-92 metal probe. |
| * Voltage range: 3.0V - 5.5V | * Voltage range: 3.0V - 5.5V | ||
| * Temperature measuring range: -55°C / +125°C | * Temperature measuring range: -55°C / +125°C | ||
| * Accuracy: ±0.5°C (-10°C / +85°C range) | * Accuracy: ±0.5°C (-10°C / +85°C range) | ||
| - | * Can be powered by DATA 1 wire | + | * The sensor converts 12-bit temperature values to a digital signal (750 ms max. delay) |
| + | * Can be powered by DATA wire (parasitic mode) | ||
| ==== Unipi 1-wire temperature sensor ==== | ==== Unipi 1-wire temperature sensor ==== | ||
| - | [[https://www.unipi.technology/1-wire-teplotni-senzor-p63|Unipi 1-Wire temperature sensor]] is available in four cable lengths, and features an RJ45 connector. It can be connected to older [[https://www.unipi.technology/cs/neuron-c2|Unipi Neuron]] controllers with RJ45 1-Wire port, or the [[https://www.unipi.technology/1-wire-hub-s-8-porty-p31|Unipi 8-port 1-Wire hub]]. The latest Unipi Neuron design and the entire Unipi Axon line are equipped with 3-wire screw terminals, for which the **RJ45 connector cannot be used**. | + | [[https://www.unipi.technology/1-wire-teplotni-senzor-p63|Unipi 1-Wire temperature sensor]] is available in four cable lengths, and features an RJ45 connector. It can be connected to older [[https://www.unipi.technology/cs/neuron-c2|Unipi Neuron]] controllers with RJ45 1-Wire port, or the [[https://www.unipi.technology/cables-reductions-hubs-c41| Unipi 8-port 1-Wire hub]]. The latest Unipi Neuron design and the entire Unipi Axon line are equipped with 3-wire screw terminals, for which the **RJ45 connector cannot be used**. |
| + | |||
| + | {{ :en:hw:03-1wire:1-wire-temperature-meter.png?400&direct |}} | ||
| If you need to connect the sensor to a controller with the 3-wire terminal, there are two methods you can do so: | If you need to connect the sensor to a controller with the 3-wire terminal, there are two methods you can do so: | ||
| - | - cut off the sensor's RJ45 connector, put ferrules onto the wires and and wire them into the 3-wire terminal according to [[https://kb.unipi.technology/_media/en:automation:02-glossary:infografika_axon.png|this schematic]] | + | - cut off the sensor's RJ45 connector, put ferrules onto the wires and wire them into the 3-wire terminal according to [[https://kb.unipi.technology/_media/en:automation:02-glossary:infografika_axon_2.png|this schematic]] |
| - | - use the [[https://www.unipi.technology/kabelova-1-wire-redukce-rj45-3-pin-svorkovnice-p325|cable reduction]] | + | - use the [[https://www.unipi.technology/cables-reductions-hubs-c41|cable reduction and Unipi 1-Wire hubu]] |
| - | Senzor disponuje čtyřvodičovým zapojením pro vyšší spolehlivost rozvětvených sítí, v případě potřeby je ale možné jej upravit pro třívodičové zapojení. | + | The sensor uses a four-wire connection for better reliability of branched networks. If needed, it can be modified for a three-wire connection. |
| - | {{ :en:hw:03-1wire:1-wire-temperature-meter.png?direct |}} | + | === Possible connections === |
| + | == Connecting a single 1-Wire temp. sensors to a Unipi controller == | ||
| - | === Možnosti zapojení === | ||
| - | == Zapojení jednoho 1-Wire teploměru ke kontroléru Unipi == | ||
| {{:en:hw:1wire_temp_eng.png?400|}} | {{:en:hw:1wire_temp_eng.png?400|}} | ||
| - | == Zapojení dvou 1-Wire teploměrů ke kontroléru Unipi skrze RJ45 splitter == | + | == Connecting a pair of 1-Wire temp. sensors to an Unipi controller using the RJ45 splitter == |
| {{:en:hw:splittereng.png?400|}} | {{:en:hw:splittereng.png?400|}} | ||
| - | == Připojení více 1-Wire senzorů pomocí 1-Wire hubu == | + | == Connecting multiple sensors using the 1-Wire hub == |
| {{:en:hw:hub_simple_eng.png?400|}} | {{:en:hw:hub_simple_eng.png?400|}} | ||
| - | == Vytvoření sítě 1-Wire senzorů pomocí několika 1-Wire hubů == | + | == Creating a network of 1-Wire sensors using multiple 1-Wire hubs == |
| {{:en:hw:hubeng.png?400|}} | {{:en:hw:hubeng.png?400|}} | ||
| - | ==== Nástěnné teplotní a/nebo vlhkostní senzory 1W-T-IB2 a 1W-TH-IB2 ==== | + | ==== 1W-T-IB2 / 1W-TH-IB2 on-wall temperature and/or humidity sensors ==== |
| - | V nabídce Unipi naleznete i kompaktní nástěnné interiérové 1-Wire senzory řady 1W-T/H-IB2, které jsou určeny pro odečet teploty (model [[https://www.unipi.technology/cs/nastenny-teplotni-senzor-1w-t-ib2-p350|1W-T-IB2]]), případně teploty a relativní vzdušné vlhkosti (model [[https://www.unipi.technology/cs/nastenny-teplotni-vlhkostni-senzor-1w-th-ib2-p351|1W-TH-IB2]]) v interiérech budov. Senzory jsou vybaveny čtyřvodičovou šroubovací svorkovnicí a je možné je upravit pro zapojení do třívodičové svorkovnice i pro konektor RJ45. | + | Unipi product listing also contains the 1W-T/H-IB2 compact on-wall sensors for measuring temperature ([[https://www.unipi.technology/nastenny-teplotni-senzor-1w-t-ib2-p350|1W-T-IB2]]) or temperature and relative air humidity ([[https://www.unipi.technology/nastenny-teplotni-vlhkostni-senzor-1w-th-ib2-p351|1W-TH-IB2]]) in building interiors. The sensors feature a four-wire screw terminal and can be modified for connection both to 3-wire connector and the RJ45 connector. |
| - | + | ||
| - | === Možnosti zapojení ==== | + | |
| - | + | ||
| - | == Zapojení pro třívodičovou svorkovnici == | + | |
| - | Tuto možnost využijte v případě, že chcete ke kontroléru Unipi Neuron či Unipi Axon připojit pouze jeden senzor | + | |
| - | + | ||
| - | {{:cs:hw:senzor_dratovani_3pin.png?100|}} | + | |
| - | + | ||
| - | == Zapojení pro konektor RJ45 == | + | |
| - | Konektor RJ45 využijete zejména ve třech případech | + | |
| - | - potřebujete ke kontroléru Unipi Neuron či Unipi Axon zapojit dva senzory pomocí [[https://www.unipi.technology/cs/1-wire-2-port-splitter-p327|dvojportového rozbočovače]] | + | |
| - | - potřebujete zapojit jeden senzor ke kontroléru Unipi Neuron se starším 1-Wire konektorem RJ45 | + | |
| - | - potřebujete zapojit více senzorů pomocí [[https://www.unipi.technology/cs/1-wire-hub-s-8-porty-p31|osmiportového rozbočovače]] | + | |
| - | + | ||
| - | {{:cs:hw:senzor_dratovani_rj45.png?200|}} | + | |
| - | + | ||
| + | === Connection options ==== | ||
| + | == 3-wire screw terminal == | ||
| + | This option is suited for cases where you need to connect only a single sensor to Unipi Axon or Unipi Neuron controller | ||
| + | {{:cs:hw:senzor_dratovani_3pin_2.png?100|}} | ||
| + | ===== RJ45 connector ===== | ||
| + | Modification for the RJ45 connector is useful in three major cases: | ||
| + | - you need to connect a pair of sensors to Unipi Neuron or Unipi Axon controller using the [[https://www.unipi.technology/1-wire-2-port-splitter-p327|2-port splitter]] | ||
| + | - you need to connect a single sensor to an Unipi Neuron with the older RJ45 1-Wire port. | ||
| + | - you need to connect multiple sensors using the [[https://www.unipi.technology/1-wire-hub-s-8-porty-p31|8-port hub]]. | ||
| + | {{:cs:hw:senzor_dratovani_rj45.png?200| }} | ||
| + | {{ :cs:hw:rj45-pinout_1-wire.png?nolink&400|}} | ||
