Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:hw:05-1-wire [2019/10/16 06:49] jan_kozak [Firvena attachable sensor with hose clamp] |
— (current) | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ======%hide 1-Wire Devices ===== | ||
- | ====== 1-Wire ====== | ||
- | 1-Wire is a device communications bus system that provides low-speed data, signaling, and power over a single conductor. | ||
- | UniPi tries to maximize the reliability of the whole network by serializing the bus as much as possible. This is achieved by using 4 wires (GND, VCC, Data-IN, Data-OUT). This four-wire design is used in our 1Wire temperature sensors and 8port hubs. | ||
- | |||
- | ===== 1-Wire thermometers ===== | ||
- | |||
- | {{ :en:hw:03-1wire:xds18b20.jpg?direct&100|}} | ||
- | |||
- | The DS18B20 is widely used [[en:automation:02-glossary:1wire-hidden|1-Wire]] sensor in TO-92 package. | ||
- | |||
- | * Power supply range is 3.0V to 5.5V | ||
- | * Measures temperatures from -55°C to +125°C (-67°F to +257°F) | ||
- | * ±0.5°C accuracy from -10°C to +85°C | ||
- | * Converts 12-bit temperature to digital word in 750 ms (max.) | ||
- | * Can be powered from data l | ||
- | |||
- | ==== UniPi 1-wire temperature sensor ==== | ||
- | The [[https://www.unipi.technology/1-wire-temperature-sensor-p63?categoryId=3|UniPi 1-Wire temperature sensor]] is equipped with RJ45 connector, so it is easy to connect to [[en:hw:02-neuron|UniPi Neuron]] controllers and [[en:hw:06-1-wire-hub|UniPi 1-Wire hub]]. In order to connect the sensor to UniPi Axon, you have to cut off the connector, put on the ferrules (see [[en:automation:01-how-to:wiring-hidden|wiring guidelines]]) and screw it to the Axon's 1-Wire connector according to [[en:automation:02-glossary:1wire-hidden#wire_on_unipi_axon|this pinout]] | ||
- | |||
- | The sensor introduces a 4 wire connection for better reliability of larger network, which can be converted to 3 wire version for simplification. | ||
- | |||
- | {{ :en:hw:03-1wire:1-wire-temperature-meter.png?direct |}} | ||
- | |||
- | ==== Connecting a single 1-Wire sensor to the Unipi controller ==== | ||
- | {{:en:hw:1wire_temp_eng.png?600|}} | ||
- | |||
- | ==== Connecting a pair of 1-Wire sensors to the Unipi controller via RJ45 splitter ==== | ||
- | {{:en:hw:splittereng.png?600|}} | ||
- | |||
- | ==== Connecting multiple 1-Wire sensors through a 1-Wire hub==== | ||
- | {{:en:hw:hub_simple_eng.png?600|}} | ||
- | |||
- | ==== Creating a multi-hub extensive network of 1-Wire sensors==== | ||
- | {{:en:hw:hubeng.png?600 | ||
- | |}} | ||
- | |||
- | =====%hide Firvena attachable sensor with hose clamp ==== | ||
- | = | ||
- | |||
- | FIXME | ||
- | |||
- | =====%hide Firvena sensor for air conditioning pipes ===== | ||
- | |||
- | FIXME |