This is an old revision of the document!

Advanced mode of digital outputs: PWM

The PWM stands for Pulse-Width Modulation. It is for generating a square signal of given frequency and certain duty cycle on a digital output. Typically, it is used for regulating a DC powered component in a way the analog regulation cannot achieve.

Let's take a 24V DC motor for example. To achieve 100% RPMs, you have to supply it with 24V. Logically, to achieve 10% RPMs, you have to supply it 24V/10 = 2.4V. But if you apply this voltage, the motor will not even start, because of the friction and its load. And if it starts, its torque will be very low. This is one of many downsides of analogue regulation.

The PWM works only on digital outputs, that means it can only output 0V or 24V. To achieve the regulation, the PWM generates a square signal of given frequency. That means it will periodically set the output ON and OFF. The parameter of the regulation is the duty cycle - a proportion of the ON time and OFF time within one period. When the duty cycle is represented in percents and the value is 50%, the output signal will be 50% of the period ON and the rest will be OFF. If the duty cycle is 66%, it will be 66% of the cycle ON and 34% OFF.

One of the parameters you need to set is the frequency of the PWM. You have to set this value according to your regulated system. The rule of thumb is - the slower the system you regulate is, the lower the frequency can be and vice versa. Take for example a large water heater. It can take up to several hours to heat a large tank of water to desired temperature, therefor we don't need high frequency regulation. Even tenths or hundredths of Hz will be sufficient. For regulating a LED light, we need to set the frequency to at least 100Hz, because lower frequencies would be visible by naked eye.

Another thing considering the frequency is the switching element you are turning ON and OFF. If it is a mechanical relay, you have to use very low frequency or you could destroy it. If it is SSR relay, MOSFET or IGBT transistor, you can set couple of kHz or even MHz (always referr to the datasheet of the component).

The frequency of the PWM in UniPi depends on the used resolution. See below.

Second parameter of the PWM is the resolution. This value indicates in how many steps we want to divide the regulation. If the resolution is 3, we can set the duty cycle to 3 values: 0%, 50% and 100%. If the resolution is 11, we can set it from 0% to 100% in the steps of 10%.

In UniPi controllers, you can set the resolution up to 65536 steps.

The duty cycle, as mentioned above, is the actual value of the regulation. Typically, you will encounter PWM duty cycle represented as a percentage of the ON time in regard of the period. In the Mervis however, the duty cycle is represented by the number of resolution steps. Let's see how to calculate this value.

resolution - 1 duty_cycle [mervis] = ------------------- * duty_cycle [%] 100

1. example

resolution = 101 steps (0 - 100% in the step of 1%)

duty_cycle [%] = 34

resolution - 1 101 - 1 duty_cycle [mervis] = ------------------- * duty_cycle [%] = ------------------- * 34 = 34 100 100

For resolution of 101 steps and desired duty_cycle of 34% we need to set the duty cycle in Mervis to 34. That was easy, let's try something more complicated.

2. example

resolution = 6 steps (0 - 100% in the step of 20%)

duty_cycle [%] = 40%

resolution - 1 6 - 1 duty_cycle [mervis] = ------------------- * duty_cycle [%] = -------------- * 40 = 2 100 100

For resolution of 6 steps and desired duty_cycle of 40% we need to set the duty cycle in Mervis to 2.

As you can see, when the only correct values of duty_cycle [mervis] is between 0 and resolution - 1. These values you will set from the program.

Unfortunatelly, you cannot set the frequency and the resolution values in the Mervis directly. The variables for configuring PWM in Mervis are called PWM_Cycle and PWM_Prescale and you need to calculate their values according to desired resolution and frequency:

PWM_Cycle = resolution - 2 4.8 * 10^7 PWM_Prescale = ------------------------------- - 1 frequency * ( resolution - 1)

The PWM_Cycle and PWM_Prescale variables are 16bit words, therefor you can set only integer values 0 - 65535. If the result of your calculations is real number, you need to either round it, or change the parameters frequency or resolution.

Alternatively, to get the resolution and frequency from PWM_Cycle and PWM_Prescale values, use these equations:

resolution = PWM_Cycle + 2 4.8 * 10^7 frequency = ---------------------------------------- ( PWM_Cycle + 1) * (PWM_Prescale + 1)

1. example

Resolution = 11 (duty cycle 0 - 100% with 10% steps)

Frequency = 4kHz

PWM_Cycle = resolution - 2 = 11 - 2 = 9 4.8 * 10^7 4.8 * 10^7 PWM_Prescale = ------------------------------- - 1 = --------------------- - 1 = 1199 frequency * ( resolution - 1) 4000 * ( 11 - 1 )

2. example

Resolution = 41 (step 2.5%)

Frequency = 0.1Hz

PWM_Cycle = resolution - 2 = 41 - 2 = 39 4.8 * 10^7 4.8 * 10^7 PWM_Prescale = ------------------------------- - 1 = ------------------- - 1 = 12.631 * 10^6 frequency * ( resolution - 1) 0.1 * (39 - 1 )

As you can see, with given resolution and frequency, the PWM_Prescale is larger than its maximum value 65535. We either have to increase the frequency, resolution or both.

3. example

Resolution = 10001 (step 0.01%)

Frequency = 0.1Hz

PWM_Cycle = resolution - 2 = 10001 - 2 = 9999 4.8 * 10^7 4.8 * 10^7 PWM_Prescale = ------------------------------- - 1 = ------------------------- - 1 = 47999 frequency * ( resolution - 1) 0.1 * (10001 - 1 )

With increased resolution, we are able to achieve lower frequencies and vice versa. For high frequency PWM, we need to sacrifice the resolution.

The PWM_Cycle and PWM_Prescale are configuration variables of the UniPi module and cannot be changed from the program. Select the UniPi module in the Left panel. In the Properties panel, you can find the PWM_Cycle and PWM_Prescale variables. Set those according to your calculations. We will set it to PWM_Cycle = 99 and PWM_Prescale = 119. This will set the frequency to 4kHz with resolution of 101.

After each setting of the configuration, you need to download the configuration into the module. Right click on the module name in the Left panel and select the UniPi - Configure module option.

For configuration of the module, the PLC has to be in Commissioning mode. If not, the Mervis IDE will warn you and automatically switch to the mode. If so, just confirm the dialog by clicking on Next >.

The dialog with progress of the configuration will appear.

And after the finishing of the configuration, you can confirm the dialog by clicking on OK.

Let's check which variables we have available for working with PWM. Select the Variable browser tab on the Main window. Under the Name column, enter the PWM into the search box. You should see similar list.

Turn on the Debugging and in the column PLC Value, you will see the current PWM value of DO ports 1.01 - 1.04. If you didn't change it previously, you should see zeros. Change the value of PWM_1.01 to 50 and confirm by clicking on V or submiting with ENTER.

We can hook up the oscilloscope to the UniPi's DO 1.01 and check the waveform.

And we can see the frequency of the wave is 4kHz with 50% duty cycle.