Differences

This shows you the differences between two versions of the page.

--- en:sw:01-mervis:connecting-to-extension-xg18-hidden [2020/06/15 14:34] – [Connecting the Extension xG18 to Mervis IDE] avsetula
+++ en:sw:01-mervis:connecting-to-extension-xg18-hidden [2021/08/05 12:40] (current) – avsetula
@@ Line 3: / Line 3: @@
 <WRAP half column 81%>
 Are you looking for an affordable temperature measurement solution, need to read the temperature at longer distances, or want to automate a boiler room? Then the [[https://www.unipi.technology/unipi-extension-xg18-p331|Extension xG18]] is the ideal solution.
+This compact module is designed as a simple and reliable tool capable of reading temperature from up to 8 Unipi 1-Wire temperature sensors (DS18B20). Modbus RTU protocol on RS-485 serial line is used to provide the data to the control system.
 </WRAP>
 <WRAP half column 15%>
 ;;#
-<html><span class="dev-tag dev-axon">Axon</span></html> \\
+<html><span class="dev-tag dev-patron">Patron</span></html> \\
 <html><span class="dev-tag dev-neuron">Neuron</span></html> \\
+<html><span class="dev-tag dev-gate">Gate</span></html> \\
+<html><span class="dev-tag dev-axon">Axon</span></html> \\
 <html><span class="dev-tag dev-extens">Extension</span></html>
 ;;#
 </WRAP>
 </WRAP>
-This compact module is designed as a simple and reliable tool capable of reading temperature from up to 8 Unipi 1-Wire temperature sensors (DS18B20). Modbus RTU protocol on RS-485 serial line is used to provide the data to the control system.
 Each 1-Wire channel is dedicated for just the one 1-Wire sensor with a RJ45 connector, which highly increases reliabily of the measurements.
@@ Line 19: / Line 21: @@
 The following guide will lead you through both hardware and software settings, and will also show you how to set it up in Mervis IDE.
-==== Prerequisites ====
+<WRAP center round box>
+<html><span class="kbBlue-H4alt">Prerequisites:</span></html>
   * [[https://www.unipi.technology/axon-c20 | Unipi controllers]] and [[en:files:software:mervis:00-start|Mervis IDE v2.3.0]]
-  * [[https://www.unipi.technology/accessories-c4|24V DC power supply]]
+  * [[https://www.unipi.technology/accessories-c4|24 V⎓ power supply]]
   * local network connectivity (any network switch or router)
   * [[https://www.unipi.technology/en/rozsirujici-moduly-c40|Extension xG18 module]]
   * at least one Unipi 1-Wire temperature sensors with an RJ45 connector
+</WRAP>
 ===== 1 Connecting xG18 to an Unipi PLC =====
-Extension xG18 communicates with the PLC using a two-wire RS-485 connection. The module can be powered by the same power source as the PLC (if the power supply's specification allows it). Alternatively, you can use a standalone 5-24V DC power supply. As to temperature sensors, simply plug them into the available RJ45 ports.
+Extension xG18 communicates with the PLC using a two-wire RS-485 connection. The module can be powered by the same power source as the PLC (if the power supply's specification allows it). Alternatively, you can use a standalone 5-24 V⎓ power supply. As to temperature sensors, simply plug them into the available RJ45 ports.
+{{ :en:sw:01-mervis:connecting-to-extension-xg18-001-en.png?nolink&800 |}}
-{{ :en:sw:01-mervis:connecting-to-extension-xg18-001-en.png?nolink |}}
 ===== 2 Attaching the xG18 to a Mervis IDE project =====
@@ Line 54: / Line 60: @@
 Now we need to add a device to the channel. You can do it bu Autodetection, or, if you don't have the xG18 at hand, manually.
-==== 2.1 Automatic detection using module autodetect ====
+==== 2.1 Automatic detection using module autodetect ====
 Right-click on the Modbus_RTU channel and choose **Unipi - modules autodetect**.
@@ Line 72: / Line 78: @@
 {{ :en:sw:01-mervis:connecting-to-extension-xg18-008-en.png |}}
-==== 2.2 Manual addition using a library device ====
+==== 2.2 Manual addition using a library device ====
 Right-click on the Modbus_RTU channel and click on **Add Library Device**.
@@ Line 94: / Line 100: @@
 {{ :en:sw:01-mervis:connecting-to-extension-xg18-013-en.png |}}
 ===== 3 Device configuration =====
@@ Line 99: / Line 106: @@
 The following communication parameters can be set via DIP switches:
-  * Address .................................. 1 – 15 (Address 0 = SW configuration from Modbus registers is used)
+  * Address .................................. 1–15 (Address 0 = SW configuration from Modbus registers is used)
   * Baud rate ............................... 9600 / 19200 baud
   * Parity ....................................... none / even
@@ Line 120: / Line 127: @@
 {{ :en:sw:01-mervis:connecting-to-extension-xg18-015-en.png |}}
 ==== 3.2 Hardware configuration of communication parameters through DIP switches ====
@@ Line 138: / Line 146: @@
 {{ :en:sw:01-mervis:connecting-to-extension-xg18-018-en.png |}}
 ===== 4 Practical example =====