Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:sw:01-mervis:unipi-configure-module-hidden [2021/05/03 09:44] avsetula |
en:sw:01-mervis:unipi-configure-module-hidden [2021/06/04 13:41] avsetula |
||
---|---|---|---|
Line 2: | Line 2: | ||
<WRAP group> | <WRAP group> | ||
<WRAP half column 81%> | <WRAP half column 81%> | ||
- | A Unipi Neuron/Axon consists of small computer running a GNU/Linux and HW IO modules (see inner diagram for [[en:hw:02-neuron|Neuron]] and [[en:hw:01-axon|Axon]]). These modules offer different functionality based on the IOs they present. For example [[en:automation:02-glossary:digital-inputs-hidden|digital inputs]] can act as Direct Switches, [[en:automation:02-glossary:analog-inputs-hidden|analog inputs]] can measure different quantities, [[en:automation:02-glossary:digital-outputs-hidden|digital outputs]] can output PWM and so on. Any output can have a default value, which applies right after powering up the PLC, way before the finishing the boot up sequence of the operating system. This configuration also applies to the [[en:hw:04-extensions|Unipi Extensions]], albeit they don't run any OS. | + | A Unipi Neuron/Patron consists of small computer running a GNU/Linux and HW IO modules (see inner diagram for [[en:hw:02-neuron|Neuron]] and [[en:hw:007-patron|Patron]]). These modules offer different functionality based on the IOs they present. For example [[en:automation:02-glossary:digital-inputs-hidden|digital inputs]] can act as Direct Switches, [[en:automation:02-glossary:analog-inputs-hidden|analog inputs]] can measure different quantities, [[en:automation:02-glossary:digital-outputs-hidden|digital outputs]] can output PWM and so on. Any output can have a default value, which applies right after powering up the PLC, way before the finishing the boot up sequence of the operating system. This configuration also applies to the [[en:hw:04-extensions|Unipi Extensions]], albeit they don't run any OS. |
</WRAP> | </WRAP> | ||
<WRAP half column 15%> | <WRAP half column 15%> | ||
Line 14: | Line 14: | ||
</WRAP> | </WRAP> | ||
- | <WRAP center round tip 60%> | + | |
+ | <WRAP center round tip 90%> | ||
All of these configurations are OS-independent and are permanently stored into the modules. If you receive an used Unipi unit, the best approach is to save a blank new configuration to overwrite possible unwanted settings. | All of these configurations are OS-independent and are permanently stored into the modules. If you receive an used Unipi unit, the best approach is to save a blank new configuration to overwrite possible unwanted settings. | ||
</WRAP> | </WRAP> | ||
- | + | ||
+ | /* FIXME - přeložit do EN | ||
+ | <WRAP center round important 90%> | ||
+ | Po změně parametrů u sériových linek **ttyNS** (viz: tabulka mapování portů pro [[cs:hw:007-patron:portmap|Patron]]/[[cs:hw:02-neuron:portmap|Neuron]]/[[cs:hw:01-axon:portmap|Axon]]) je třeba následně nahrát konfiguraci do kontroléru. Před nahráním konfigurace se vždy ujistěte, že ostatní nastavení (režim výstupů, výchozí hodnoty, aj.) je nastaveno správně. | ||
+ | |||
+ | Pokud se konfigurace po změně nastavení sériové linky nenahraje, může při restartování desky I/O dojít k přenastavení konfigurace sériové linky. | ||
+ | </WRAP> | ||
+ | */ | ||
In Mervis, the configuration is pushed via context menu of the connected prototype. Right click on the prototype name in the **Left Panel** and in the context menu click on "**Unipi - Configure Module**". | In Mervis, the configuration is pushed via context menu of the connected prototype. Right click on the prototype name in the **Left Panel** and in the context menu click on "**Unipi - Configure Module**". | ||