Differences

This shows you the differences between two versions of the page.

--- en:sw:02-apis:04-sysfs [2024/07/15 08:55] – kcerny
+++ en:sw:02-apis:04-sysfs [2026/07/16 11:23] (current) – updated to deb13 ofojt
@@ Line 7: / Line 7: @@
   <div id="tabs">
   <div id="tabs-container">
-      <a href=""><span class="actual-version">12 & 11</span></a>
+      <a href=""><span class="actual-version">13</span></a>
+      <a href="/en:sw:02-apis:04-sysfs-deb11-12-hidden"><span>12 & 11</span></a>
       <a href="/en:sw:02-apis:04-sysfs-deb10-hidden"><span>10</span></a>
     </div>
@@ Line 16: / Line 17: @@
 </div></html>
-====== SysFS ======
+====== Sysfs ======
 <WRAP group>
+/*
 <WRAP half column 81%>
-The SysFS driver is part of the kernel module for Unipi units with inputs and outputs and provides easy file-based access to all inputs and outputs.
+*/
+The sysfs driver is part of the kernel module for Unipi units with inputs and outputs and provides easy file-based access to all inputs and outputs.
+/*
 </WRAP>
 <WRAP half column 15%>
 ;;#
-<html><span class="dev-tag dev-iris">Iris</span></html> \\
+/*<html><span class="dev-tag dev-iris">Iris</span></html> \\* /
 <html><span class="dev-tag dev-patron">Patron</span></html> \\
 <html><span class="dev-tag dev-neuron">Neuron</span></html>
 ;;#
 </WRAP>
+*/
 </WRAP>
 ----
-<WRAP center round info 95%>
+<WRAP group center round box 95%>
-To use 1-Wire on a Unipi unit with OpenSource OS, you must install and configure OWFS. In the case of an OS with EVOK, OWFS is already installed.
+{{ :files:img_warning-line_b.png?nolink |}}
+<WRAP half column 13%>
+{{ :en:hw:08_safety-instructions_pseudo-ISO-7010-info.png?nolink |(i)}}
+</WRAP>
+<WRAP half column 83%>
+**Note:** \\
+To use 1-Wire on a Unipi unit with Base OS, you must install and configure OWFS. If the OS has Evok preinstalled, OWFS will be already installed.
 **Do not install OWFS for Mervis OS**! It uses an alternative method to work with 1-Wire and collisions could occur.
+</WRAP>
 </WRAP>
 ----
-{{page>en:sw:02-apis:04-sysfs:docu-deb11-12-hidden}}
+<html><span class="kbBlueText">Check the following examples of reading and writing I/O to get started: </span></html> \\
+All files within sysfs can be accessed in the same way.
+\\
+**DO** status reading:
+<code>cat /run/unipi-plc/by-sys/DO1.1/value</code>
+Setting the **DO** to the closed state:
+<code>echo 1 > /run/unipi-plc/by-sys/DO1.1/value</code>
+----
+**DI** status reading:
+<code>cat /run/unipi-plc/by-sys/DI1.1/value</code>
+Status reading of all first section **DI**'s:
+<code>cat /run/unipi-plc/by-sys/DI1.*/value</code>
+Status reading of all available **DI** units:
+<code>cat /run/unipi-plc/by-sys/DI[1-3].*/value</code>
+{{page>en:sw:02-apis:04-sysfs:docu-deb13-hidden}}