Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:sw:04-unipi-firmware [2021/01/14 13:23] avsetula [Unipi Software] |
en:sw:04-unipi-firmware [2021/08/06 06:58] avsetula |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| <WRAP center round info 90%> | <WRAP center round info 90%> | ||
| - | Currently, the packages are supported only for all controllers except Unipi 1.1 and Unipi 1.1. lite - those should be [[en:sw:02-apis:01-evok|installed as described here.]] | + | Currently, the packages are supported only for all units except Unipi 1.1 and Unipi 1.1. lite - those should be [[en:sw:02-apis:01-evok|installed as described here.]] |
| </WRAP> | </WRAP> | ||
| Line 32: | Line 32: | ||
| The internal firmware is NOT automatically flashed to the latest version installed using apt. This has to be done manually. | The internal firmware is NOT automatically flashed to the latest version installed using apt. This has to be done manually. | ||
| - | === Upgrading firmware in Patron/Neuron/Axon family PLC controllers === | + | === Upgrading firmware in Patron/Neuron/Axon line units === |
| The firmware can be manually upgraded or checked using the fwspi tool which resides in /opt/unipi-bin/ (newly in /opt/unipi/tools/). | The firmware can be manually upgraded or checked using the fwspi tool which resides in /opt/unipi-bin/ (newly in /opt/unipi/tools/). | ||
| Line 41: | Line 41: | ||
| <WRAP center round info 60%> | <WRAP center round info 60%> | ||
| - | To check the FW of other IO groups run <code>/opt/unipi/tools/fwspi -i 1</code> alternatively <code>/opt/unipi/tools/fwspi -i 2</code>. | + | To check the FW of other IO sections run <code>/opt/unipi/tools/fwspi -i 1</code> alternatively <code>/opt/unipi/tools/fwspi -i 2</code>. |
| </WRAP> | </WRAP> | ||
| <WRAP center round info 60%> | <WRAP center round info 60%> | ||
| - | Firmware upgrade can be done automatically on all groups available using command <code>/opt/unipi/tools/fwspi -v --auto</code> | + | Firmware upgrade can be done automatically on all sections available using command <code>/opt/unipi/tools/fwspi -v --auto</code> |
| </WRAP> | </WRAP> | ||
| Line 79: | Line 79: | ||
| <WRAP center round info 60%> | <WRAP center round info 60%> | ||
| - | The configuration of the group can be erased to the default state. This is done during the firmware upgrade by calling the fwspi utility also with -R parameter. E.g. /opt/unipi/tools/fwspi -i 0 -PR | + | The configuration of the section can be erased to the default state. This is done during the firmware upgrade by calling the fwspi utility also with -R parameter. E.g. /opt/unipi/tools/fwspi -i 0 -PR |
| </WRAP> | </WRAP> | ||
| Line 86: | Line 86: | ||
| <WRAP center round alert 80%> | <WRAP center round alert 80%> | ||
| - | Make sure that there is no other application using/communicating on the used port and do not disconnect power to the Controller or Extension. Any of this will lead to bricking the extension. | + | Make sure that there is no other application using/communicating on the used port and do not disconnect power to the unit or Extension. Any of this will lead to bricking the extension. |
| </WRAP> | </WRAP> | ||
