Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
files:software:os-images:00-start [2019/12/13 07:45]
mkudlacek
files:software:os-images:00-start [2020/01/20 13:31] (current)
avsetula
Line 1: Line 1:
-====== OS Images ====== +~~REDIRECT>​en:​files:​software:​os-images:​00-start~~
-This section contains OS images for our controllers. +
- +
-<WRAP center round info 90%> +
-Mervis OS are versioned the same way as Mervis IDE releases. Eg. Mervis OS 2.2.0.2 will work with IDE 2.2.0 but might not work with IDE 2.1.9. +
-Vice versa Mervis IDE 2.2.0 requres at least Mervis OS 2.2.0.x and might not work well with OS 1.9. +
-</​WRAP>​ +
- +
-<WRAP center round important 90%> +
-Make sure to wait a few minutes after the first boot with a new image. The internal firmware is being automatically updated! If you disconnect the power supply during this procedure, the device will be corrupted and must be sent back to us to re-flash the firmware. +
-</WRAP> +
- +
-====== Axon generation OS====== +
-The factory default Debian based OS for whole Axon generation. Please follow the turorial or attached leaflet on [[en:​hw:​01-axon:​image|how to flash newer OS versions.]] +
-===== Axon Mervis OS ===== +
-Contains Mervis tools and default ModbusTCP&​SysFS drivers. +
-{{page>​axon-mervis-os-hidden}} +
-  * {{ :​files:​software:​os-images:​unipi-axon-os-2018-11-09_v1.8.zip |UniPi-Axon-OS-2018-11-09_v1.8.zip}} +
-  * {{ :​files:​software:​os-images:​unipi-axon-os-2018-09-18_v1.7.zip |UniPi-Axon-OS-2018-09-18_v1.7.zip}} +
- +
-===== Axon OpenSource OS ===== +
-Image for development or OEM use. Includes ModbusTCP&​SysFS drivers. Evok should be installed using the apt, according to the guide on its [[https://​github.com/​UniPiTechnology/​evok#​installing-evok-on-axon-plcs | GitHub page]]. +
-{{page>​axon-opensource-os-hidden}} +
-  * {{ {{ :​files:​software:​os-images:​axon-opensource.20190923.0.zip | UniPi-Axon-OpenSource-OS-2019-09-23.zip}} +
- +
----- +
-====== Neuron generation OS====== +
-===== UniPi Mervis OS ===== +
-Images to be [[en:​sw:​01-mervis:​running-on-neuron-hidden|deployed to a uSD]] card for Neuron controllers running Mervis RT. +
-{{page>​neuron-mervis-os-hidden}} +
-  +
-Previous images for Mervis on Neuron and also UniPi 1. +
-  * {{ :​files:​software:​os-images:​unipi-neuron-mervis-os-2018-12-20_v1.9.zip |UniPi-Neuron-Mervis-OS-2018-12-29_v1.9.zip}} +
-  * {{ :​files:​software:​os-images:​unipi-neuron-mervis-os-2018-09-14_v1.7-beta.zip |UniPi-Neuron-Mervis-OS-2018-09-14_v1.7-BETA.zip}} +
- +
-<WRAP center round info 60%> +
-Since Mervis OS v1.7 the SSH is disabled by default and should be enabled by placing a file named ssh, without any extension, onto the boot partition of the SD if needed. The username is "​unipi"​ and password is "​unipi.technology"​. +
-</​WRAP>​ +
- +
-===== UniPian Neuron OS ===== +
-UniPian is Raspbian Lite based OS with all required Neuron drivers (kernel driver, overlay, RTC support, ModbusTCP, SysFS and Evok) and disabled SSH. This OS expects DHCP server running on the network. +
-<WRAP center round info 60%> +
-The SSH is disabled by default and should be enabled by one of the [[https://​www.raspberrypi.org/​documentation/​remote-access/​ssh/​ | standard Raspbian methods]]. The username and passwords are the same as on Raspbian image (pi:​raspberry). +
-</​WRAP>​ +
- +
-{{page>​neuron-opensource-os-hidden}} +
-  * {{ :​files:​software:​os-images:​unipian-neuron-os-2019-01-07-v1.9.zip |UniPian-Neuron-2019-01-07-v1.9.zip}} +
-  * {{ :​files:​software:​os-images:​unipian-neuron-os-changelog.txt |UniPian-Neuron-OS-changelog.txt}} +
- +
- +
----- +
- +
-====== UniPi 1st generation ====== +
- +
-===== UniPi Mervis OS ===== +
-Images to be [[en:​sw:​01-mervis:​running-on-neuron-hidden|deployed to a uSD]] card for UniPi 1 controllers running Mervis RT. +
-{{page>​unipi1-mervis-os-hidden}} +
- +
----- +
-====== Extension FW upgrade OS for Neurons ====== +
-This is a special image for Neurons which only purpose is to upgrade inner firmware of Extensions (xS10,​xS30,​xS50) and Neuron controllers in order to work properly with Mervis UniPi device prototypes v2.0. +
- +
-<WRAP center round info 60%> +
-It automatically tries to detect UniPi Extensions on RS485-1 at 9600/​19200/​115200bps having Modbus addresses 1-31 only using 8N1. +
-</​WRAP>​ +
- +
-The process of FW upgrade is indicated by flashing upper and lower rows of diodes. +
-<WRAP center round important 60%> +
-Do not disconnect the power supply nor from Neuron and Extension until the LEDs stops blinking! Otherwise, the devices might be bricked! +
-</​WRAP>​ +
- +
-  * {{ :​files:​software:​os-images:​unipian-neuron-os-extension_fw_upgrade-2018-09-25.zip |UniPian-Neuron-OS-Extension_FW_Upgrade-2018-09-25.zip}} +
- +
- +
-===== Opensource images ===== +
-We do not provide the ready opensource image (Like UniPian) for the first generation of UniPi. Please use the standard Raspbian Lite with Evok installed according to the guide on its [[https://​github.com/​UniPiTechnology/​evok#​legacy-installation-process-using-a-shell-script-required-for-unipi-11 | GitHub page]]. +
- +
-== Obsolete FHEM image == +
-* {{ :​files:​software:​os-images:​unipian_fhem-v0.3-rpi.zip |unipian_fhem-v0.3-rpi.zip}} includes Readme.txt +