Differences

This shows you the differences between two versions of the page.

--- en:automation:02-glossary:1wire-hidden [2022/10/10 11:27]
lpolcerova [1-Wire]
+++ en:automation:02-glossary:1wire-hidden [2023/09/06 12:37] (current)
avsetula [1W-T/H-IB, 1W-T/H-IB2, SD 115C & SD 125C]
@@ Line 48: / Line 48: @@
 | 4 | VCC (+5 V⎓) |
 | 5 | VCC (+5 V⎓) |
-| 6 | {{:files:data_0.png?nolink&15|}}1W (DATA_0) |
+| 6 | {{:files:data_0.png?nolink&15|}}1W (DATA_1) |
-| 7 | {{:files:data_1.png?nolink&15|}}1W (DATA_1) |
+| 7 | {{:files:data_1.png?nolink&15|}}1W (DATA_0) |
 | 8 | GND |
@@ Line 57: / Line 57: @@
 <WRAP center round box>
-**Note:** {{:files:data_0.png?nolink&15|}}1W, sometimes also DATA_0, is the main data wire. That said, if you connect a cable sensor with only a single data wire to the RJ45 connector, always connect it to pin 6 (eg. {{:files:data_0.png?nolink&15|}}1W pin). The {{:files:data_1.png?nolink&15|}}1W contact, sometimes also DATA_1, is a supplemental contact of Unipi sensors designed for a maximum possible bus serialization and serves for connecting the next sensor on the bus. The Unipi 1-Wire hub can serve as an example of the double-data wire principle. If you use a non-Unipi cable sensor with only a single data wire, the above-mentioned serialization with Unipi 1-Wire hub is not possible. You can, however, connect the sensor to the end of the bus (eg. as the last sensor in the hub).
+**Note:** {{:files:data_1.png?nolink&15|}}1W, sometimes also DATA_0, is the main data wire. That said, if you connect a cable sensor with only a single data wire to the RJ45 connector, always connect it to pin 7 (eg. {{:files:data_1.png?nolink&15|}}1W pin). The {{:files:data_0.png?nolink&15|}}1W contact, sometimes also DATA_1, is a supplemental contact of Unipi sensors designed for a maximum possible bus serialization and serves for connecting the next sensor on the bus. The Unipi 1-Wire hub can serve as an example of the double-data wire principle. If you use a non-Unipi cable sensor with only a single data wire, the above-mentioned serialization with Unipi 1-Wire hub is not possible. You can, however, connect the sensor to the end of the bus (eg. as the last sensor in the hub).
 </WRAP>
@@ Line 147: / Line 147: @@
 <html><span class="kbBlueText">RJ45 connection</span></html> \\
 Connection to RJ45-connector network cable is useful for star-shaped network topologies created from 1-Wire hubs. You can also use it to connect the sensor to Unipi 1.1 extension board, or to the older variants of Unipi Neuron controllers.
-All these sensors can be also connected to the [[https://www.unipi.technology/unipi-extension-xg18-p331|Unipi Extension xG18 module]]. Coloured connection scheme on the picture corresponds to the T568B connection.
+All sensors with the DS18b20 chip and parasite power support can also be connected to the [[https://www.unipi.technology/unipi-extension-xg18-p331|Unipi Extension xG18 module]].. Coloured connection scheme on the picture corresponds to the T568B connection.
 ;#;