Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | |||
en:hw:01-axon:backup2usb [2021/05/03 11:35] avsetula |
en:hw:01-axon:backup2usb [2021/08/06 14:12] (current) avsetula |
||
---|---|---|---|
Line 3: | Line 3: | ||
<WRAP group 100%> | <WRAP group 100%> | ||
<WRAP half column 81%> | <WRAP half column 81%> | ||
- | This article describes the process to backup, clone, and restore the entire filesystem of the Axon controllers including all user changes (Mervis projects, installed applications, ...). | + | This article describes the process to backup, clone, and restore the entire filesystem of the Axon units including all user changes (Mervis projects, installed applications, ...). |
</WRAP> | </WRAP> | ||
<WRAP half column 15%> | <WRAP half column 15%> | ||
Line 20: | Line 20: | ||
====== Backup process ====== | ====== Backup process ====== | ||
<WRAP center round alert 90%> | <WRAP center round alert 90%> | ||
- | During the image recovery process, all data from the recovered PLC unit is permanently deleted and the storage partition-table is reset to the factory default state. | + | During the image recovery process, all data from the recovered unit is permanently deleted and the storage partition-table is reset to the factory default state. |
</WRAP> | </WRAP> | ||
<WRAP center round alert 90%> | <WRAP center round alert 90%> | ||
Line 26: | Line 26: | ||
</WRAP> | </WRAP> | ||
<WRAP center round alert 90%> | <WRAP center round alert 90%> | ||
- | USB 3.0 flash drives may not work properly on older Axon PLC units. A USB 2.0 flash drive is recommended. The drive must always be formatted with the FAT32 file system. | + | USB 3.0 flash drives may not work properly on older Axon units. A USB 2.0 flash drive is recommended. The drive must always be formatted with the FAT32 file system. |
</WRAP> | </WRAP> | ||
Line 32: | Line 32: | ||
- Start the Axon in service mode: | - Start the Axon in service mode: | ||
- Hold and keep pressed the small recessed button on top of the Axon device case using a thin-enough tool. The button can be found next to the USB port labels on the upper side of the device. | - Hold and keep pressed the small recessed button on top of the Axon device case using a thin-enough tool. The button can be found next to the USB port labels on the upper side of the device. | ||
- | - Power up the controller while holding the button down. | + | - Power up the unit while holding the button down. |
- Wait until the device finishes booting into the Unipi service mode. This is indicated by the two rows of LEDs flashing in an alternating fashion. | - Wait until the device finishes booting into the Unipi service mode. This is indicated by the two rows of LEDs flashing in an alternating fashion. | ||
- Use a device with a web browser to connect to the Unipi Axon via Ethernet LAN or Wi-Fi. The process is slightly different between the two options: | - Use a device with a web browser to connect to the Unipi Axon via Ethernet LAN or Wi-Fi. The process is slightly different between the two options: | ||
Line 43: | Line 43: | ||
====== Restoration process ====== | ====== Restoration process ====== | ||
- | - Put the USB with all the files created using the Backup process the in **USB2** while the PLC is powered down. | + | - Put the USB with all the files created using the Backup process the in **USB2** while the unit is powered down. |
- Hold and keep pressed the small recessed button on top of the Axon. | - Hold and keep pressed the small recessed button on top of the Axon. | ||
- | - Power up the PLC. | + | - Power up the unit. |
- Wait ca 5sec until both rows of the LEDs start to light up progressively and release the button. | - Wait ca 5sec until both rows of the LEDs start to light up progressively and release the button. | ||
- | - The flashing of the PLC is in the process. | + | - The flashing of the unit is in the process. |
- Wait until both rows of LED turn off. | - Wait until both rows of LED turn off. | ||
- | - PLC is flashed and automatically restarted. | + | - Unit is flashed and automatically restarted. |