Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:hw:01-axon:lte [2020/11/10 16:17] – avsetulaen:hw:01-axon:lte [2025/05/16 09:55] (current) – [Autoswitch feature] typo ofojt
Line 1: Line 1:
 {{page>en:hw:01-axon:replacement-of-axon-hidden}} {{page>en:hw:01-axon:replacement-of-axon-hidden}}
 ====== Axon LTE ====== ====== Axon LTE ======
-<WRAP center round tip 60%>+ 
 +<WRAP group center round box 95%> 
 +{{ :files:img_warning-line_b.png?nolink |}} 
 +<WRAP half column 13%> 
 +{{ :en:hw:08_safety-instructions_pseudo-ISO-7010-info.png?nolink |(i)}} 
 +</WRAP> 
 +<WRAP half column 83%>
 Looking for a guide how to get started with LTE on **Mervis IDE**? Please see [[en:sw:01-mervis:lte-configuration-hidden|this tutorial]], otherwise continue here. Looking for a guide how to get started with LTE on **Mervis IDE**? Please see [[en:sw:01-mervis:lte-configuration-hidden|this tutorial]], otherwise continue here.
 +</WRAP>
 </WRAP> </WRAP>
  
 ===== Quick-start guide ===== ===== Quick-start guide =====
  
-<WRAP center round info 80%> +<WRAP group center round box 95%> 
-Axon series controllers are shipped with the Mervis image by default. Mervis can be disabled or you can flash the open-source image manually. +{{ :files:img_warning-line_b.png?nolink |}} 
 +<WRAP half column 13%> 
 +{{ :en:hw:09_safety-instructions_pseudo-ISO-7010-attention.png?nolink |(!)}} 
 +</WRAP> 
 +<WRAP half column 83%> 
 +Axon series units are shipped with the Mervis image by default. Mervis can be disabled or you can flash the open-source image manually. 
   * [[https://kb.unipi.technology/files:software:os-images:00-start#axon_opensource_os|open-source image]]   * [[https://kb.unipi.technology/files:software:os-images:00-start#axon_opensource_os|open-source image]]
   * [[https://kb.unipi.technology/en:hw:01-axon:image|HOW-TO Flash the OS]]   * [[https://kb.unipi.technology/en:hw:01-axon:image|HOW-TO Flash the OS]]
 +</WRAP>
 </WRAP> </WRAP>
  
Line 16: Line 29:
  
   - Insert a micro-sim supporting LTE data into the slot.   - Insert a micro-sim supporting LTE data into the slot.
-  - Log-in to the controller via SSH (or SCP).+  - Log-in to the unit via SSH.
   - Install unipi-lte package:<code>   - Install unipi-lte package:<code>
 sudo su sudo su
Line 24: Line 37:
   - Edit file /etc/unipi/lte.conf. **APN setting is mandatory** (LTE service is turned off if this line in the file is missing or is commented). You can use built-in nano editor to do this. The APN parameter should be provided by your network operator, so ''internet'' is the default value.    - Edit file /etc/unipi/lte.conf. **APN setting is mandatory** (LTE service is turned off if this line in the file is missing or is commented). You can use built-in nano editor to do this. The APN parameter should be provided by your network operator, so ''internet'' is the default value. 
   - In the same way, set the PIN parameter if SIM is PIN-protected.   - In the same way, set the PIN parameter if SIM is PIN-protected.
-  - Restart your controller. Be patient, registration to the mobile network can take tens of seconds. When registered, NET LED lights up.+  - Restart your unit. Be patient, registration to the mobile network can take tens of seconds. When registered, NET LED lights up.
   - During normal operation, "Mobile network" LED indicators SIM, NET, INT should be ON while blinking SIG indicates signal strength.    - During normal operation, "Mobile network" LED indicators SIM, NET, INT should be ON while blinking SIG indicates signal strength. 
   - In case of any problem, check the Syslog for more info (you can use grep command to filter messages from the unipi-lte service).   - In case of any problem, check the Syslog for more info (you can use grep command to filter messages from the unipi-lte service).
Line 31: Line 44:
 By default, the unipi-lte Linux service provides automatic handling with the default network gateway according to the WAN availability on both main and backup network interfaces. The main network adapter is usually wired ethernet (eth0) while the backup is realized by the LTE modem. In the Linux routing table, the default GW routes for both of these interfaces should be always present. When a "swap" of these interfaces is necessary, the unipi-lte daemon automatically increases/decreases their metrics. By default, the unipi-lte Linux service provides automatic handling with the default network gateway according to the WAN availability on both main and backup network interfaces. The main network adapter is usually wired ethernet (eth0) while the backup is realized by the LTE modem. In the Linux routing table, the default GW routes for both of these interfaces should be always present. When a "swap" of these interfaces is necessary, the unipi-lte daemon automatically increases/decreases their metrics.
  
-Therefore, it is necessary to continually keep the metrics as positive non-zero values. This is ensured by a DHCP client when DHCP is active on the main network interface but **it must be assured manually if static IP is configured on the main interface** (as static routes have zero metrics as default). As an example, you can put a constant to the interface’s configuration file at ///etw/network/interfaces.d//.+Therefore, it is necessary to continually keep the metrics as positive non-zero values. This is ensured by a DHCP client when DHCP is active on the main network interface but **it must be assured manually if static IP is configured on the main interface** (as static routes have zero metrics as default). As an example, you can put a constant to the interface’s configuration file at ///etc/network/interfaces.d//.
  
-Then, the ///etw/network/interfaces.d/**eth0**// file for static IP configuration may look like:+Then, the ///etc/network/interfaces.d/**eth0**// file for static IP configuration may look like:
 <code> <code>
 # Example static IP configuration for unit belonging to LAN # Example static IP configuration for unit belonging to LAN
Line 60: Line 73:
  
 ===== Useful hints ===== ===== Useful hints =====
-  * for optimal signal strength **it is necessary to use an external antenna** installed in an open space (eg. outside any enclosures). External antenna is included in the package of each LTE controller - during the purchase, you can also choose between the default antenna with magnetic mount, or a larger one with on-wall mount. Both antennas can be also purchased [[https://www.unipi.technology/others-c42|separately]]+  * for optimal signal strength **it is necessary to use an external antenna** installed in an open space (eg. outside any enclosures). External antenna is included in the package of each LTE unit - during the purchase, you can also choose between the default antenna with magnetic mount, or a larger one with on-wall mount. Both antennas can be also purchased [[https://www.unipi.technology/others-c42|separately]]
   * Operate both Wi-Fi and LTE simultaneously is not recommended.    * Operate both Wi-Fi and LTE simultaneously is not recommended. 
   * The Ethernet interface is set as primary while the LTE acts as a backup by default.   * The Ethernet interface is set as primary while the LTE acts as a backup by default.
(Still can't find what you're looking for?)