Technical parameters
Extension
The following article contains storage, installation and working conditions on Unipi Extension modules.
Connector description
| Terminal marking | Meaning |
|---|---|
| +24V | Power terminal - positive pole |
| GND | Power terminal - negative pole |
| DI | Digital input |
| DIGND | Digital input common terminal – negative pole |
| RO | Relay output |
| COM | Common relay terminal |
| AI | Analog input |
| AIR | Analog input for resistance measurement |
| AIS | Current source for resistance measurement |
| AOV | Analog voltage output |
| AGND | Analog input/output common terminal - negative pole |
| RS485-A / RS485-B | RS-485 communication line terminals |
Storage, installation and operating conditions
| Operating conditions | Temperature 0 … +55 °C, relative humidity 10 … 95 %, without aggressive substances, condensing vapour and fog |
| Storing conditions | Temperature -25 … +70 °C, relative humidity 10 … 95 %, without aggressive substances, condensing vapour and fog |
| Altitude | up to 2000 m |
| EMC immunity zone | B (IEC 61000-6-2 compliant) |
| Protection class | I |
| Overvoltage category | II |
| Pollution degree | 2 |
| Ingress Protection (IEC 529) | IP 20 |
| Operation position | Any |
| Installation | On 35mm DIN rail (EN 60715, 35mm) into distribution cabinet; holder and screws (M3x5, DIN 965, PH 1) included |
| Connection | Pluggable terminal blocks |
| Wire gauge | Max. 2.5 mm2 |
| Terminal spacing | 5.08 mm |
| Terminal tightening torque | Max. 0.4 Nm |
Power supply
| Rated voltage - SELV | 24 V⎓ (±5%) |
| Power consumption | Typ. 3 W Max. 12 W |
| Reverse polarity protection | Yes |
Dimensions and weight
| Dimensions | 72 × 90 × 56 mm (DIN holder 3 mm) |
| Weight | depending on the model - from 140 g to 300 g |
Unipi Extension xS:
Digital inputs
| Input type | SINK |
| Input terminal | DI |
| Common ground | DIGND |
| Log. 0 | < 3 V DC |
| Log. 1 | > 7 V DC |
| Maximum voltage | 35 V DC |
| Non-defined state | 3-7 V DC |
| Input resistance for TRUE | 6 200 Ω |
| Voltage drop on DI diode | 1.2 V |
| Minimum pulse length | 20 μs |
| 0–>1 / 1–>0 delay | Typ. 20 μs / 60 μs |
| Maximum CNT counter input frequency | 10 kHz |
| LED indication | Yes |
| Galvanic isolation | Yes (Basic, between DI groups) |
| Insulation voltage (pulse) | 1500 V |
Relay outputs
Please note: The data below represent a selection of the most important parameters and serve only as a quick reference.
Detailed information can be found in the product datasheet provided by the relay manufacturer: FTR-F3AA024E-HA
| Output type | Electromechanic non-shielded relay |
| Output terminal | RO |
| Common terminal | COM |
| Contact type | Normally open (SPST-NO) |
| Used relay type | FTR-F3AA024E-HA |
| Maximum switching voltage | 250 V AC 30 V DC |
| Maximum switching current | 5 A |
| Maximum common terminal current | 10 A |
| Short-term current overload | 5 A |
| Mechanical lifespan | 5 000 000 |
| Electrical lifespan | Up to 100 000 (according to the connected load) |
| Operate/release time | 10 ms |
| Designed for load character | AC-15, DC-13 (resistive) |
| Load handling | External (RC, varistor, diode, thermistor) |
| Short circuit protection | No |
| Overvoltage protection | No |
| LED indication | Yes |
| Galvanic isolation | Yes (Basic) |
| Insulation voltage (pulse) | 2500 V between RO and RO 4000 V between RO and all other circuits |
![/!\](/_media/en:hw:01_safety-instructions_iso-7010-w001.png "/!\")
Warning:
Only extra-low voltage (ELV) can be connected to the relay output RO 1 of Unipi Extension xS5* modules (xS51, xs52, etc.)! The parameters specified above must also be respected.
Analog inputs (type 1)
| Input terminals | AI, AIS |
| Common conductor | AGND |
| Galvanic isolation | Yes |
| Input functions | 0–10 V⎓ voltage measurement, 0–20 mA current measurement, 0–1960 Ω or 0–100 kΩ resistance measurement |
| Resolution | 24 bits (resistance measurement), 16 bits (voltage and current measurement) |
| Conversion time | 400 ms (resistance measurement), 60 μs (voltage and current measurement) |
| Protection type | Integrated overvoltage protection |
| Maximum input voltage | 15 V⎓ |
| Measurement accuracy | ±0.2 % |
| Input resistance (voltage measurement) | 44 kΩ |
| Input resistance (current measurement) | 100 Ω |
Analog inputs (type 2)
| Input terminals | AI / AIS |
| Common ground | AGND / AIR |
| Overvoltage protection | Integrated transil |
| Maximum voltage | 15 V⎓ |
| Maximum current | 40 mA |
| Connection | SINK (measurement relative to the ground) |
| Galvanic isolation (pulse) | 1500 V between AI and all other circuits |
Attention:
Measurements outside the specified range may reduce the accuracy of the measurement and/or reduce the input impedance.
In case of strong interference to the cable (EN 6100-6-4), the measurement accuracy can be reduced to 1 % of the measured value. The use of additional EMC filters and shielded cabling is recommended (connect shield to the ground point of the device).
Voltage 0-10 V
| Available on device | xS53, xS54 |
| Measuring range | 0.1–10 V |
| Accuracy | ±0.2 % (of range) |
| Input resistance | 12 kΩ ±20 % |
| Resolution | 24 bits |
| Conversion time | 200 ms |
Voltage 0-2 V
| Available on device | xS53, xS54 |
| Measuring range | 0.1–2 V |
| Accuracy | ±1 % (of range) |
| Input resistance | 1 MΩ ±50 % |
| Resolution | 24 bits |
| Conversion time | 200 ms |
Current 4-20 mA
| Available on device | xS53, xS54 |
| Measuring range | 1–20 mA |
| Accuracy | ±0.2 % (of range) |
| Input resistance | 100 Ω ±1 % |
| Resolution | 24 bitů |
| Conversion time | 200 ms |
Resistance 2 kΩ
| Available on device | xS52, xS54 |
| Measuring range | 75–2000 Ω |
| Connection | Two-wire |
| Measuring current | < 0.3 mA (average) |
| Resolution | 24 bits |
| Accuracy | ±0.3 % (of value) / 0.5 Ω |
| Conversion time | 200 ms |
| Compatible sensors | Pt100/Pt1000 (tol. ±0.75 ˚C), Ni100/Ni1000/2k reostat, etc.. |
Please note:
The compensation of the lead resistance and the conversion to temperature according to the selected sensor is up to the user application.
Resistance 20 kΩ
| Available on device | xS52, xS54 |
| Measuring range | 1–20 kΩ |
| Connection | Two-wire |
| Measuring current | < 0.03 mA (average) |
| Resolution | 24 bits |
| Accuracy | ±1 % (of value) / 10 Ω |
| Conversion time | 200 ms |
| Compatible sensors | Reostat |
Analog outputs
| Output terminals | AOV |
| Common conductor | AGND |
| Galvanic isolation | Yes |
| Output functions | 0–10 V⎓ voltage source |
| Resolution | 12 bits |
| Conversion time | 300 μs |
| Protection type | Integrated overvoltage protection |
| Output voltage range | 0-10 V⎓ |
| Output accuracy | ±0.5 % |
RS-485 interface
| Terminals | RS485-A, RS485-B |
| Baudrates | 2400 bps 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps |
| Pull-up/pull-down resistors | No |
| Terminating resistor | Builtin attachable, 120 Ω (RS485-END) |
| Galvanic isolation (pulse) | 1500 V between RS-485 and all other circuits |
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
